Page 3 of 3 FirstFirst 123
Results 21 to 24 of 24

Thread: jeppesen and AF

  1. #21
    Colin,

    The ARINC software update instructions are on the last page of the software install instructions. The ARINC.hex file is one of the several files contained in the software zip file downloaded from our website. If you have the software on an SD card still, you should see the ARINC.hex file on the card.
    ---
    Trevor Conroy
    Technical Support
    Advanced Flight Systems
    Support@Advanced-Flight-Systems.com

  2. #22
    Hmmm, the ARINC software update instructions are NOT on the last page of the instructions. On the instructions index list (P1) it says" error in link".
    I can see the ARINC.hex file on the sd card but when I try to install it at the correct place on the systems admin page it says "file not found".

  3. #23
    ARINC P/N: 71,400 Software**Installation Instructions**(S/N: ALL)

    1. Install new ARINC software (if you do not have an ARINC adaptor you can skip this step)
    a) If you have an ARINC adapter check the software version using [CHECK] -> [MAINT] ->
    [ABOUT] selection. Verify that your ARINC adaptor is running version 4.0 software, if it is
    already running version 4.0 you can skip the following steps.
    b) Enter the EFIS calibration menu using the new shortcut: [CHECK] -> [MAINT] -> [ADMIN] ->
    then hold [CALIBRATION] button for 2 seconds.
    c) Cycle power to the ARINC adaptor using the aircraft Master Switch. If the ARINC module is
    powered on the same source as the EFIS the internal EFIS battery should keep the EFIS
    running during the power cycle.
    d) Select the following menu:
    1. Admin Settings
    21. System Maintenance
    4. Upgrade ARINC Software
    e) Press the start button to begin loading the new code. The screen will say, “Loading….xxx”.
    Where xxx is the number of bytes transferred.
    f) When the screen prints “Done.”, you can remove the card and reboot the EFIS and ARINC
    Module by cycling the power to both units.
    2. Remove the Software card from the EFIS and install the new MAP data card in the EFIS slot.
    3. Verify that the new ARINC software installed
    The following menu will display the current software versions: [CHECK] -> [MAINT.] -> [ABOUT]
    ---
    Trevor Conroy
    Technical Support
    Advanced Flight Systems
    Support@Advanced-Flight-Systems.com

  4. #24
    ARINC P/N: 71,400 Software**Installation Instructions**(S/N: ALL)

    1. Install new ARINC software (if you do not have an ARINC adaptor you can skip this step)
    a) If you have an ARINC adapter check the software version using [CHECK] -> [MAINT] ->
    [ABOUT] selection. Verify that your ARINC adaptor is running version 4.0 software, if it is
    already running version 4.0 you can skip the following steps.
    b) Enter the EFIS calibration menu using the new shortcut: [CHECK] -> [MAINT] -> [ADMIN] ->
    then hold [CALIBRATION] button for 2 seconds.
    c) Cycle power to the ARINC adaptor using the aircraft Master Switch. If the ARINC module is
    powered on the same source as the EFIS the internal EFIS battery should keep the EFIS
    running during the power cycle.
    d) Select the following menu:
    1. Admin Settings
    21. System Maintenance
    4. Upgrade ARINC Software
    e) Press the start button to begin loading the new code. The screen will say, “Loading….xxx”.
    Where xxx is the number of bytes transferred.
    f) When the screen prints “Done.”, you can remove the card and reboot the EFIS and ARINC
    Module by cycling the power to both units.
    2. Remove the Software card from the EFIS and install the new MAP data card in the EFIS slot.
    3. Verify that the new ARINC software installed
    The following menu will display the current software versions: [CHECK] -> [MAINT.] -> [ABOUT]
    ---
    Trevor Conroy
    Technical Support
    Advanced Flight Systems
    Support@Advanced-Flight-Systems.com

Similar Threads

  1. International Map Data from Jeppesen - a myth.
    By Jherbert in forum Map Database
    Replies: 2
    Last Post: 06-21-2011, 06:54 PM
  2. Jeppesen Map Data
    By smithhb in forum Map Database
    Replies: 1
    Last Post: 08-26-2010, 08:10 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •