Results 1 to 10 of 10

Thread: AOA calibration manual for AFS-5600

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1

    AOA calibration manual for AFS-5600

    Hi - Finally got my AOA installed and am about to do the calibration. I found the RV6 settings here, but the actual calibration including hangar-setting I can't find in my manuals or maybe I am looking the wrong place ?
    Does anyone have the EFIS instructions for calibration ?? I want to nail it before heading to the skies with a fellow pilot to do the inflight settings.

    regards
    Per
    RV-6A
    Denmark

  2. #2
    Advanced Flight Systems Shawn McGinnis's Avatar
    Join Date
    Sep 2012
    Location
    Canby, OR
    Posts
    861
    http://dynonavionics.com/af-series-d...ation.php#5000

    AF-5000 Series Pilot Guide Version 15.0 Page 35
    Shawn McGinnis

    Advanced Flight Systems
    support@advanced-flight-systems.com

  3. #3
    Ok - thanks- I understand that there is no hangar calibration needed, but when I look in the AOA setup- I usually see a speed indication of around 12kts - even inside sealed hangar ?
    I am using the Ray-Allen Flaps position indicator - and it works fine, but I can't seem to get the donut to turn on and off. The "Use flaps position" is set to yes.
    The AOA is also crossed with red - see photo.

    Name:  IMG_7794.jpg
Views: 1683
Size:  72.0 KB

    Name:  IMG_7795.jpg
Views: 1530
Size:  35.7 KB

    regards
    Per

  4. #4
    Advanced Flight Systems Shawn McGinnis's Avatar
    Join Date
    Sep 2012
    Location
    Canby, OR
    Posts
    861
    Looks like your AOA Module Config isn't setup properly.
    What type of AOA pressure receiver are you using (Dynon Pitot/Wing Ports)?
    Where do they connect (EFIS or SV-ADAHRS)?
    Shawn McGinnis

    Advanced Flight Systems
    support@advanced-flight-systems.com

  5. #5
    Quote Originally Posted by Shawn McGinnis View Post
    Looks like your AOA Module Config isn't setup properly.
    What type of AOA pressure receiver are you using (Dynon Pitot/Wing Ports)?
    Where do they connect (EFIS or SV-ADAHRS)?
    the connection is at the EFIS (OS:1) (Older version AFS-5600) and I use wing ports.

    The system was bought 2nd hand, but the AOA was never used by the previous owner. I seem to recall some serial number to be entered to activate the AOA ? is this correct ?

    If you need files from the EFIS let me know.

    regards
    Per

  6. #6
    I took a look at the System.AFD file for my PFD unit.
    It looks like AOA is not installed/enabled ? The tube fittings are on both my screens.

    Sk


    Thoughts ?

  7. #7
    Advanced Flight Systems Shawn McGinnis's Avatar
    Join Date
    Sep 2012
    Location
    Canby, OR
    Posts
    861
    My guess is that the screen wasn't purchased with the AOA key. Use CHECK -> ABOUT and see if on your Keys: line it includes AOA. If not contact Tricia at 503-263-0037 x 2 or sales@advanced-flight-systems.com with your serial numbers from the same CHECK -> ABOUT page and she can verify and send you the keys.
    Shawn McGinnis

    Advanced Flight Systems
    support@advanced-flight-systems.com

  8. #8
    I found it... it was disabled on the system... so I enabled and the AOA responds now.
    Last question: what is best practice - as I have 2 units with AOA modules installed. Should they both run internal and no network between each other or should PFD take the lead and transmit AOA data to the secondary screen ?

  9. #9
    Advanced Flight Systems Shawn McGinnis's Avatar
    Join Date
    Sep 2012
    Location
    Canby, OR
    Posts
    861
    Two units with the wing ports connected to the back of the units should cross-check each other by using AOA Module Config: HW:WING NET:TXD.
    Shawn McGinnis

    Advanced Flight Systems
    support@advanced-flight-systems.com

  10. #10
    perfect - many thanks.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •