Search:

Type: Posts; User: neville

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. 5000 series install manual v15.1 starting on page...

    5000 series install manual v15.1 starting on page 169
  2. Replies
    1
    Views
    3,274

    Rotax CAN BUSS fuel flow

    With a 5600 (OS1) and a Rotax 912iS I get fuel flow from the CAN buss. What should the Admin page fuel flow settings be set to?
  3. Replies
    6
    Views
    81,468

    More info; put stick in 5600, all charts show...

    More info; put stick in 5600, all charts show proper expire date.
  4. Replies
    6
    Views
    81,468

    Just did download, found erratic program, in the...

    Just did download, found erratic program, in the middle of sectional suddenly got "download complete" then program continued download, Got msg " problem with Montana chart", then continued, got...
  5. Beyond the normal TCW capacity test done every...

    Beyond the normal TCW capacity test done every time power it interrupted to the 5600 are several more involved TCW tests which are described in the TCW manual, My TCW manual is REV 2.3.
  6. Replies
    5
    Views
    7,481

    Interesting thing about the auto function. I have...

    Interesting thing about the auto function. I have 5600 with SV-261 and 2020 GPS. If plane is in hangar with marginal GPS signals the auto function may shift from GND to ALT erratically. Also on the...
  7. Replies
    2
    Views
    7,152

    Thanks! I recently installed the SV-261 and GPS...

    Thanks! I recently installed the SV-261 and GPS 2020 for adds-b out using AFS 5600 (OS-1). Installation was simple and set-up instructions were excellent. Took a/c to avionics shop for testing and...
  8. Replies
    2
    Views
    7,152

    extended squittter

    When the SV-261 transponder is put in the standby mode are all transmissions stopped or does data transmission continue?
  9. Replies
    3
    Views
    7,983

    Shawn, Does this issue have any impact on the...

    Shawn, Does this issue have any impact on the Advanced p/n 74109 Adsb out or the SV-GPS -2020 ?
  10. Replies
    3
    Views
    6,214

    I have to correct the statement on the previous...

    I have to correct the statement on the previous thread. I finally beat the weather and went flying. The old HP field starts out as TP and remains that . Also the HorsePower block in Instrument...
  11. Replies
    3
    Views
    6,214

    Thanks for the response Shawn. Yes It is there. I...

    Thanks for the response Shawn. Yes It is there. I hate to admit that I never had looked at the HP field before engine is started. But I see that the field starts out as TP until engine is started...
  12. Replies
    3
    Views
    6,214

    Rotax 912iS throttle position

    Hi Shawn, while your adding to the list of software additions how about adding throttle position for 912iS to the engine page. It is on the can buss.
  13. Replies
    1
    Views
    4,753

    AF 5600 and GDL 39 Bluetooth data

    Will a AFS 5600 with Bluetooth option accept and display the Garmin GDL 39 Bluetooth ADS-B in data?
  14. Replies
    1
    Views
    4,874

    Rotax 912iS fuel pressure

    The Rotax owners forum has a discussion going on at the present which concerns the source of fuel pressure readings on a glass panel. The issue is that the 912iS uses the pressure in the air box as...
  15. Replies
    4
    Views
    15,697

    you might check the wiring. When I installed the...

    you might check the wiring. When I installed the VDO sensor on my Rotax engine I used the wiring diagram included with the sensor. Oil pressure readings wrong. Sent the sensor back to Advanced for...
  16. Replies
    1
    Views
    5,299

    flight data down load

    question; on flight data spread sheet column D, AOA, if that represents angle of attack should there not be a decimal place? On column AW, AOA wing PSF,
    what is PSF? Possibly pressure per square...
  17. Replies
    5
    Views
    10,015

    I see on the Rotax Owners Forum that some...

    I see on the Rotax Owners Forum that some operators are asking their EFIS manufacturer for the addition of throttle position , mainly for ease of adjusting throttle for ECO
    (fuel economy) position.
  18. Replies
    5
    Views
    10,015

    Software installed: V X10.04.16-MV16 (Dec 18...

    Software installed: V X10.04.16-MV16 (Dec 18 2014)
    OS: 1 (Dec 2 2011)
    FS: 1.0
    BB; 5
    ...
  19. Replies
    5
    Views
    10,015

    Rob, I contacted Rotax they replied to the...

    Rob, I contacted Rotax they replied to the affirmative that the CAN buss contains throttle position in percent. I would appreciate your adding it to the list of things to do.
  20. Replies
    5
    Views
    10,015

    rotax 912iS sport throttle position

    With the upgrade of the rotax 912iS to 912iS sport the starting sequence changed in that the throttle position
    prior to start is now dependent on outside temperature. It is my impression that the...
  21. Replies
    4
    Views
    8,711

    contacted Shawn, they are on the problem and...

    contacted Shawn, they are on the problem and working for a fix. In the mean time I am using a short USB extender cord to have easy access to the USB port
    and leave the stick out until after start...
  22. Replies
    4
    Views
    8,711

    starts normally without usb stick installed

    starts normally without usb stick installed
  23. Replies
    4
    Views
    8,711

    ver 10.04.16/system start up

    I have installed the subject version and a factory preloaded usb stick. The 5600 startup goes thru three tries to complete the startup. With power supplied to the system the first try sequence is;...
  24. Thread: AFS intercom

    by neville
    Replies
    10
    Views
    26,582

    Rob, thanks for the input. I will be purchasing...

    Rob, thanks for the input. I will be purchasing the AFS intercom as it appears that I can eliminate the extra audio mixer board and will have ample voltage to support
    the electrete element without...
  25. Thread: AFS intercom

    by neville
    Replies
    10
    Views
    26,582

    To answer Issac, I currently have 5.2v on the...

    To answer Issac, I currently have 5.2v on the element. It works OK but when I TX I hear more background noise than what I have found to be normal
    Thanks for the response
Results 1 to 25 of 33
Page 1 of 2 1 2