Search:

Type: Posts; User: Shawn McGinnis

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    745

    You can send in the system logs and...

    You can send in the system logs and svautopilot.log files and we could take a look. If you haven't already, try re-running the servo calibration process.
  2. Replies
    1
    Views
    347

    That seems odd. There may be something more going...

    That seems odd. There may be something more going on.

    I would recommend asking TCW directly but I've seen this done with relays like below, or with diodes.
    460
  3. Replies
    5
    Views
    695

    You should still be able to move/zoom it with the...

    You should still be able to move/zoom it with the joystick. To change plates touch the center of the plate screen then touch plate again.
  4. Replies
    4
    Views
    745

    Have you performed the autopilot calibration...

    Have you performed the autopilot calibration process within calibration? It has you move the control surfaces to all corners then plays back the movements to confirm.
  5. Replies
    5
    Views
    695

    What method are you using to bring up the plates?

    What method are you using to bring up the plates?
  6. You might get away with dropping GSA as you are...

    You might get away with dropping GSA as you are not reporting NACv to an transponder but RMC and GGA are required.
  7. Replies
    1
    Views
    711

    We have a engineer working on them at the moment....

    We have a engineer working on them at the moment. No firm release schedule though.
  8. Replies
    11
    Views
    2,489

    I'll have Rob test it today.

    I'll have Rob test it today.
  9. That list is the setup for the 18-5Hz puck. PGRMT...

    That list is the setup for the 18-5Hz puck. PGRMT is not used by the Advanced Deck displays.

    You should be able to configure the Ublox's Main Talker ID to 1 - GP (GPS) and avoid the system...
  10. Replies
    1
    Views
    460

    Yes, here are some threads: ...

    Yes, here are some threads:

    http://advanced-flight-systems.com/forum/threads/1409-Uavionix-Echo-UAT-gt-AF-4500
    http://advanced-flight-systems.com/forum/threads/1411-ADS-B-for-4500
  11. Replies
    3
    Views
    695

    Flagged glide slope is a nav signal issue. 2kr...

    Flagged glide slope is a nav signal issue. 2kr would be the nav antenna signal being invalid or low strength. Did you change anything between the Val and its antenna?
  12. Replies
    6
    Views
    1,883

    I am guessing that the traffic targets are taking...

    I am guessing that the traffic targets are taking all the available serial port time and not letting the FIS-B through. The weather should normally show up within about 10 minutes of reception.

    If...
  13. I'd probably wire all of this to the DB9 and move...

    I'd probably wire all of this to the DB9 and move whatever is on Serial #4 over to serial #2. The green to the 4500's RXD, with power and ground than the 4500's TXD would go to the 327.

    The EFIS...
  14. Replies
    4
    Views
    1,379

    If that was happening to an EFIS with the tubing...

    If that was happening to an EFIS with the tubing disconnected I would be checking for a blockage/kink in the internal pitot line or a bad sensor.
  15. Do you have an internal engine monitor or an...

    Do you have an internal engine monitor or an SV-EMS-2XX?

    An internal engine monitor supplies 10V to Pin 2 Trim Pwr and to Pin 29 Amp Hall Pwr. So you can either tee the wires together or if the...
  16. Replies
    11
    Views
    2,489

    The IFD may not have a route that allows external...

    The IFD may not have a route that allows external devices to talk to each other. Does it work when connected directly to the AF-5000?
  17. Replies
    1
    Views
    597

    This feature was added 3 years ago to the EFIS....

    This feature was added 3 years ago to the EFIS. You should be able to use the touchscreen to allow typing in of the number. Check that you are running the latest software...
  18. Replies
    1
    Views
    553

    The 175 manual shows that it can output NMEA...

    The 175 manual shows that it can output NMEA which works with an AF-5600. So you should be able to wire the blue data out and a ground into any available serial port of the AF-5600. Select No In/NMEA...
  19. Replies
    5
    Views
    1,090

    1. Yes it requires an AF-ARINC module to talk to...

    1. Yes it requires an AF-ARINC module to talk to the 4500 -> AP -> and Navigator
    2. That's already part of the software once the AP is connected to the AF-4500 with ARINC.
    3. The AF-4500 can...
  20. Replies
    11
    Views
    2,489

    Are you running v15 software in the EFIS? As long...

    Are you running v15 software in the EFIS? As long as the EFIS doesn't hear incoming GDL90 on the WiFi, and its getting ADS-B information in via serial, it will send out GDL90 to its attached wireless...
  21. Replies
    2
    Views
    821

    Are you seeing UAT traffic received on the CHECK...

    Are you seeing UAT traffic received on the CHECK -> ABOUT -> WX page of the EFIS?
  22. Replies
    6
    Views
    1,883

    You could also double check that you are using...

    You could also double check that you are using ADSB115K and that the Stratux Serial Output Baudrate is set to 115200.

    Are you flying in a really dense traffic area? What are you seeing on the...
  23. Replies
    1
    Views
    660

    The AF-4500 was developed to interface with...

    The AF-4500 was developed to interface with NavWorx and Freeflight boxes which had you configure your N-number into the receiver for onboard filtering of targets. At this time there is no plan to add...
  24. In short, the SD card isn't recommended or...

    In short, the SD card isn't recommended or necessary with the current AF-5000 software.

    Some users find it easier to use the SD card for updating software, maps, or downloading logs which is fine;...
  25. The SD Card should not remain in the display...

    The SD Card should not remain in the display during normal operation. Its also probably named AFS_DATA which is confusing the unit. Rename it to something else like AFS_SD or really anything but...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4