Search:

Type: Posts; User: Shawn McGinnis

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 21 minute(s) ago.

  1. Replies
    8
    Views
    1,069

    When reading these lines the first block, [...

    When reading these lines the first block, [ 29.546681], is the system run time in seconds. So its perfectly normal indications of the equipment being discovered.
  2. Replies
    3
    Views
    77

    Adapters seem to work, I would check with local...

    Adapters seem to work, I would check with local camera and electronics shops. Anything <=2GB will work so you can get away with using old 128MB cards as well.
  3. Replies
    3
    Views
    68

    Sounds like the PFD needs to be sent back.

    Sounds like the PFD needs to be sent back.
  4. Replies
    3
    Views
    68

    My gut is saying that your ethernet jack might...

    My gut is saying that your ethernet jack might have a cracked pin. Try applying some finger pressure to the connector on one EFIS then the other and see if the data comes back when physically...
  5. Correct you wont have anything in those spots. ...

    Correct you wont have anything in those spots.


    If you don't have trim position indicators you don't need the pins.


    If you have a flap position indicator that would have you move 34 to 9.
    ...
  6. You will connect pin 6 of the P-Mags to SV-EMS...

    You will connect pin 6 of the P-Mags to SV-EMS pins 32/33 if they are 12V signal output or pins 34/35 for 5V signal levels. Here is a list of all conversions from Internal EMS to SV-EMS. Kavlico...
  7. The AF2MAPUS.AFM contains only the occasional...

    The AF2MAPUS.AFM contains only the occasional navaid within the Canadian boundary. The data is supplied for USA and its territories.
  8. If using the Garmin 18x disconnect the EFIS TX...

    If using the Garmin 18x disconnect the EFIS TX connection to the 18x's RX pin this will help keep it alive longer.
  9. Replies
    2
    Views
    886

    Congratulations of finishing the build. To make...

    Congratulations of finishing the build. To make sure we are on the same page can you verify that you are running 7.5.0 software on the EFIS?...
  10. Replies
    6
    Views
    1,760

    Only the Non-S has the replaceable clock battery....

    Only the Non-S has the replaceable clock battery. The AF-4500 does have a soldered in battery but it was made obsolete with software so no replacement is required.
  11. Replies
    21
    Views
    5,304

    What Rob was saying is you need to select [WIFI]...

    What Rob was saying is you need to select [WIFI] as your source not [XMWX] as that is for only for paid SiriusXM Weather subscriptions with a WxWorx Receiver. [WIFI] would be from your DRX. You will...
  12. Replies
    3
    Views
    1,221

    If you find a way the experimental community...

    If you find a way the experimental community would love to hear.
  13. Replies
    21
    Views
    5,304

    I really don't have experience with the product,...

    I really don't have experience with the product, give uAvionics a call. They have always been really helpful.
  14. Replies
    1
    Views
    978

    Interesting use case, I'll we'll add it as a...

    Interesting use case, I'll we'll add it as a requested feature.
  15. Replies
    1
    Views
    988

    Sometimes the BIOS setting can get out of...

    Sometimes the BIOS setting can get out of configuration, try removing the USB to see if it allows it to boot. Otherwise contact us for an RMA.
  16. Replies
    3
    Views
    1,232

    Your screens don't have the required "OS:5"...

    Your screens don't have the required "OS:5" hardware to communicate with the WiFi adapter. They would need to be sent in for upgrade.
  17. Replies
    1
    Views
    956

    It's probably an internal problem with the...

    It's probably an internal problem with the display itself, last couple times it's been an internal power supply issue which is easy to see thermally. Contact us for a RMA to get it sorted.
  18. Replies
    3
    Views
    1,213

    Once you have wired as described on page 86 you...

    Once you have wired as described on page 86 you will calibrate the position shown on page 90.

    You can also reference this drawing for your internal engine board connector:...
  19. Thread: E-Mag

    by Shawn McGinnis
    Replies
    3
    Views
    1,988

    It should work if you use a 5V signal level....

    It should work if you use a 5V signal level. Otherwise you might need to modify the analog module to accept higher voltage pulses. You will also need to change the Pulses per revolution in the...
  20. The "SERVOS" item on the CHECK -> ELEC page...

    The "SERVOS" item on the CHECK -> ELEC page should give you the status of power applied to the autopilot servos. If you flip the physical switch are you seeing the status change from off to on? When...
  21. Replies
    1
    Views
    810

    Depends on what generation screens you are...

    Depends on what generation screens you are running. Current AF-5000T displays with Vx15 software should be synchronizing automatically when saving settings within calibration. Are your screens all...
  22. Replies
    2
    Views
    894

    Glad it's working! Blue skies.

    Glad it's working! Blue skies.
  23. Replies
    4
    Views
    1,922

    Pin 13 on the EFIS Expansion connector...

    Pin 13 on the EFIS Expansion connector is where Volts 2 is on the AF-5000 Series displays. This pin isn't pulled through into the ACM.
  24. Replies
    2
    Views
    907

    The sensor wires, if not relieved, can begin to...

    The sensor wires, if not relieved, can begin to crack as the exit the housing. I've also seen bad spark plug wires / connections cause this due to the EMI noise. Also from alternator regulators going...
  25. Replies
    21
    Views
    5,304

    https://mlimxgb6oftt.i.optimole.com/iOeAD64.AtMc~3...

    https://mlimxgb6oftt.i.optimole.com/iOeAD64.AtMc~34070/w:426/h:128/q:auto/https://uavionix.com/wp-content/uploads/2019/08/Apple-Store.png ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4