Search:

Type: Posts; User: Paul Collins

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    2,498

    Thanks and I am sorry I did not give my call back...

    Thanks and I am sorry I did not give my call back number. It is 208-861-8257. So here are my answers;
    1. The shield wire is grounded at the P-mag. I will move this if you feel that might help....
  2. Replies
    8
    Views
    2,498

    Thank you Jonathon! This was just what the box...

    Thank you Jonathon! This was just what the box wanted!!
    Paul Collins
  3. Replies
    8
    Views
    2,498

    Well, I ran the engine for the first time to day...

    Well, I ran the engine for the first time to day and the tach was significantly incorrect with wildly varying numbers and extreme speeds shown. What did I get wrong? Please feel free to call me to...
  4. Replies
    8
    Views
    2,498

    Yes, I do have the internal EMS. I very much...

    Yes, I do have the internal EMS. I very much appreciate your making sure I am doing the right thing!
    So, just run the wire from pin 33 to the Emag tach output. Sounds good.
    Thanks!
    Paul Collins...
  5. Replies
    8
    Views
    2,498

    Installing P-Mags

    I have updated my ignition systems to two P-mags and have a question about how to attach the sensor for the tach to my 5400.
    Is the voltage from the 5400 12 volts or do I need to use the diode that...
  6. Replies
    8
    Views
    90,830

    Very good idea. I like those options on-left...

    Very good idea. I like those options on-left side partial - off
    Paul C
  7. Replies
    0
    Views
    1,224

    Deleting HITS approaches

    As part of my learning curve, I established HITS descent profiles on my approach to my home airport - KEUL. It appears however that they are now etched into the airport files - or whatever - as they...
  8. Replies
    3
    Views
    3,911

    Actually, you now must use two fingers to select...

    Actually, you now must use two fingers to select on/off for views.
    Paul Collins
    N8ZV
  9. Replies
    3
    Views
    3,911

    Thanks. I did figure it out. I was not being...

    Thanks. I did figure it out. I was not being "touchy" enough.
    Paul Collins
    N8ZV
  10. Replies
    3
    Views
    3,911

    5400 touch screen operation

    After the recent upgrade, I can no longer select the views on the 5400 by touch and drag. I there a new way that I need to select the various options?
    Thank you,
    Paul Collins
    N8ZV
  11. Ouch! they should listen to you!! Paul Collins...

    Ouch! they should listen to you!!
    Paul Collins
    N8ZV
  12. Thanks. I went through the information on the...

    Thanks. I went through the information on the website and it was easy to get the proper files loaded and verified!
    On thing you might tell folks that use the Seattle Avionics ChartData Manager -...
  13. What files can I delete after downloading the update

    After I downloaded the update to V16 (which went well) when I re-start the AFS 5400 with the USB in place, I still get the message to update the system.
    What files can I delete from the USB?
    Y...
  14. Replies
    3
    Views
    48,213

    Thanks for the explanation. The system works...

    Thanks for the explanation. The system works great, and so far no CO.
    Paul Collins
    N8ZV
  15. Replies
    3
    Views
    48,213

    Interesting. The Aithre folks had me put the...

    Interesting. The Aithre folks had me put the sensor into pin 12, the power into pin 19 and then ground to aircraft ground. It works in this set-up. Again, this is somewhat different.
    Paul C
  16. Replies
    3
    Views
    48,213

    Aithre CO monitor

    I am looking to install an Aithre CO monitor. Can you direct me to the correct image of the wiring diagram to refer to?
    Their website is www.aithreaviation.com . Especially information to get the...
  17. Replies
    10
    Views
    176,254

    Interested as well.

    Interested as well.
  18. Replies
    5
    Views
    121,657

    I tap on the right side of the screen to pull up...

    I tap on the right side of the screen to pull up various options (I have a 5400). Then I tap on approach option, tap the lower right knob and get to the correct approach plate and select that. When...
  19. Replies
    5
    Views
    121,657

    Yes, the software has been updated. Paul Collins...

    Yes, the software has been updated.
    Paul Collins
    N8ZV
  20. Replies
    5
    Views
    121,657

    Adjusting a approach plate

    When I set an approach plate up on my 5400, I only have about 30 seconds to move the approach plate around on the screen before it "locks up". To move/adjust it again I need to effectively re-load...
  21. Replies
    9
    Views
    102,961

    Ok, I tried it and it worked! Here is what I did...

    Ok, I tried it and it worked! Here is what I did to change to approach airport for the plates;
    Push D (direct)
    dial in the proper airport
    push the right knob (On the 5400)
    select APPRCH
    Make...
  22. Replies
    9
    Views
    102,961

    I will try as well. It might be some quirk...

    I will try as well. It might be some quirk (?correct word?) on my system. We shall see.
    Thanks, and on we go,
    Paul Collins
    N8ZV
  23. Replies
    9
    Views
    102,961

    So, you start with a direct-to entry? Does that...

    So, you start with a direct-to entry? Does that change the APPLATE display reference airport?
    Paul Collins
    N8ZV
  24. Replies
    9
    Views
    102,961

    No, I have not been doing a direct flight with...

    No, I have not been doing a direct flight with the AFS 5400 - I do that on the IFD440. Maybe I need to set the direct course with the AFS and see if the 440 then works with the new approach.
    Paul...
  25. Replies
    9
    Views
    102,961

    Well, what happens is when I load an approach on...

    Well, what happens is when I load an approach on the IFD440, with the Advanced Flight Systems 5400 set on CDI/GNAV1 in both sites, the first approach loaded shows up on the APPLATE view (You get...
Results 1 to 25 of 31
Page 1 of 2 1 2