Search:

Type: Posts; User: rvdave

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: AOA calibration

    by rvdave
    Replies
    4
    Views
    106

    The donut comes on with full flaps only, not sure...

    The donut comes on with full flaps only, not sure how it would be half calibrated but I’ll try it again and report back with changes, but after this Michigan winter weather settles down.
  2. Thread: AOA calibration

    by rvdave
    Replies
    4
    Views
    106

    Photo of aoa settings ...

    Photo of aoa settings


    https://i.postimg.cc/RJzsHkLQ/533-B6-C6-B-3-B48-497-E-8-F4-E-E4-E46-D38-CC78.jpg
  3. Thread: AOA calibration

    by rvdave
    Replies
    4
    Views
    106

    AOA calibration

    I’ve never been able to get my aoa calibrated to where it is close to being accurate or trusted. Not sure if the button press during calibration is super critical or if the timing of the flying...
  4. Replies
    3
    Views
    387

    After your suggestion that it may be input...

    After your suggestion that it may be input related I increased volume out of 5600 to audio panel and that took care of that problem. Must have been below input threshold of audio panel.
  5. Replies
    3
    Views
    387

    I have the remote PS Engineering pac15ex with the...

    I have the remote PS Engineering pac15ex with the audio input to either 1,2, or 4– not sure at this time but it’s an unswitched input to the audio panel. I know I didn’t tie it to 3 since that one...
  6. Replies
    3
    Views
    387

    Audio annunciations cut out midsentence

    This has been going on for a while with my 5600 and current software and have been trying to see diagnosable patterns but haven’t been able to. The aural annunciations cut out mid sentence...
  7. Replies
    1
    Views
    475

    Earthx battery monitoring thru efis

    Recently installed the earthx battery with fault line wired to input to efis. During a recent fault the warning came on the screen but it doesn’t flash according to a logical code to interpret what...
  8. Recently did the ifr checkride in my rv10 3...

    Recently did the ifr checkride in my rv10 3 screen afs system. Examiner was ok with allowing only map page on pfd and efis on mfd center screen. That allowed non-precision approach to be performed...
  9. Replies
    3
    Views
    1,396

    By chance found a defective bnc connection at nav...

    By chance found a defective bnc connection at nav radio input. Was a strand of ground cable caught between crimp ring and center conductor intermittently shorting. Must have been a late night...
  10. Replies
    3
    Views
    1,396

    Only checking connectors, maybe where the problem...

    Only checking connectors, maybe where the problem lies.
  11. Replies
    9
    Views
    2,859

    I will have to verify if it actually switches to...

    I will have to verify if it actually switches to next airport app plate according to flight plan but know if you select direct to airport it will show up.
  12. Replies
    9
    Views
    2,859

    No I set direct to on ifd then it shows up in...

    No I set direct to on ifd then it shows up in flight plan on 5600 so it should be the airport in cue for approach plate.
  13. Replies
    9
    Views
    2,859

    Ok I see what you’re saying, I was thinking...

    Ok I see what you’re saying, I was thinking something else. I know if I select direct to an airport, then select plates on my 5600 the plates for that airport will be selectable. Do you select...
  14. Replies
    9
    Views
    2,859

    I didn’t know the IFD would cue the plates for...

    I didn’t know the IFD would cue the plates for the 5000 series, how are you getting that to happen, I don’t have that feature now, can you share settings?
  15. Replies
    3
    Views
    1,396

    Remote nav lost glideslope

    I have the Val nav2kr remote nav receiver as a nav source for my 5600, use it as backup or secondary for vor and ils approaches but recently have lost glideslope on an ils approach. Seems to have...
  16. Replies
    4
    Views
    3,895

    What do you have the max airspeed set to?

    What do you have the max airspeed set to?
  17. Thread: Traffic to ipad

    by rvdave
    Replies
    11
    Views
    5,301

    Not sure, maybe Rob will chime in.

    Not sure, maybe Rob will chime in.
  18. Thread: Traffic to ipad

    by rvdave
    Replies
    11
    Views
    5,301

    I believe you need the wifi module, then set iPad...

    I believe you need the wifi module, then set iPad to afs WiFi.
  19. Thread: What autopilot

    by rvdave
    Replies
    2
    Views
    1,650

    The tt Vizion 385 integrates well with afs efis...

    The tt Vizion 385 integrates well with afs efis providing push button level, push button 180, cws in addition to coupled approaches, intercepts. Does all you’re asking about. Also with Dynon...
  20. Replies
    0
    Views
    895

    New software no nav frequency

    Has anyone else noticed with new v15.01.09 software the on screen nav frequency defaults to 108.00 and can’t be changed? I’m just wondering if it’s something with my system but don’t see any...
  21. Thread: Traffic to ipad

    by rvdave
    Replies
    11
    Views
    5,301

    Traffic to ipad

    I am now getting traffic sent from 5600 via WiFi to ForeFlight on my iPad. Like it. Wondering if FlyQ is supported with advanced flight systems, thinking about trying FlyQ.
  22. Replies
    14
    Views
    10,924

    I’m planning on future earthex and would be...

    I’m planning on future earthex and would be interested.
  23. Replies
    22
    Views
    35,437

    The ifd540 manual will show you how to flight...

    The ifd540 manual will show you how to flight plan but the 540 is nice that it will auto sequence (if setup is set to auto miss), then if cdi is selected on afs efis to ifd navigator, if wired...
  24. Replies
    20
    Views
    8,090

    I have been flying with gpss set at 25 and seems...

    I have been flying with gpss set at 25 and seems to be a good value for correct lateral needle centering and on course to runway for lpv approaches.
  25. Replies
    2
    Views
    1,974

    Is there documentation how to hook this up and...

    Is there documentation how to hook this up and settings for ifd?
Results 1 to 25 of 202
Page 1 of 9 1 2 3 4