Search:

Type: Posts; User: rvdave

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Vpx disappears

    by rvdave
    Replies
    2
    Views
    225

    No xm but I will send logs to see if you can find...

    No xm but I will send logs to see if you can find something, thanks.
  2. Thread: Vpx disappears

    by rvdave
    Replies
    2
    Views
    225

    Vpx disappears

    Been a continuous nuisance on secondary not primary screen that my electrical configuration of vpx goes gray on both secondary screens. Have to every now and then add and save vpx in order to...
  3. Thread: NAV Radio

    by rvdave
    Replies
    3
    Views
    359

    The VAL2KR remote nav receiver works well with...

    The VAL2KR remote nav receiver works well with afs 5600. Initially I had trouble but it ended up being a bad coax connection in my wiring. Now I can confidently use it as vor guidance or ils...
  4. Thread: AOA calibration

    by rvdave
    Replies
    10
    Views
    1,965

    Not understanding how those numbers correspond to...

    Not understanding how those numbers correspond to display colors, should that number in aoa display match the bar color segment in mode actually flying?
  5. Thread: AOA calibration

    by rvdave
    Replies
    10
    Views
    1,965

    Recalibrated aoa and got satisfactory results. ...

    Recalibrated aoa and got satisfactory results. Now question is what parameter controls when the aoa comes on screen during declutter and what triggers when audio warning sounds angle angle push and...
  6. Replies
    0
    Views
    640

    Afs 5600 traffic to ifd550

    I have adsb472 to 5600 and recently wired in my ifd550 per afs manual to get traffic info and weather to the ifd. So far everything is communicating but I’m getting a ghost traffic indicating my own...
  7. Thread: Inset windows

    by rvdave
    Replies
    0
    Views
    546

    Inset windows

    Wondering the possibility of getting the hsi inset as a window option. It would make a good backup navigating monitor on another screen rather than having to fill the screen with the efis and lose...
  8. Thread: AOA calibration

    by rvdave
    Replies
    10
    Views
    1,965

    My flap angle sensor is tied to vpx, 5600.

    My flap angle sensor is tied to vpx, 5600.
  9. Thread: AOA calibration

    by rvdave
    Replies
    10
    Views
    1,965

    The donut comes on with full flaps only, not sure...

    The donut comes on with full flaps only, not sure how it would be half calibrated but I’ll try it again and report back with changes, but after this Michigan winter weather settles down.
  10. Thread: AOA calibration

    by rvdave
    Replies
    10
    Views
    1,965

    Photo of aoa settings ...

    Photo of aoa settings


    https://i.postimg.cc/RJzsHkLQ/533-B6-C6-B-3-B48-497-E-8-F4-E-E4-E46-D38-CC78.jpg
  11. Thread: AOA calibration

    by rvdave
    Replies
    10
    Views
    1,965

    AOA calibration

    I’ve never been able to get my aoa calibrated to where it is close to being accurate or trusted. Not sure if the button press during calibration is super critical or if the timing of the flying...
  12. Replies
    3
    Views
    1,363

    After your suggestion that it may be input...

    After your suggestion that it may be input related I increased volume out of 5600 to audio panel and that took care of that problem. Must have been below input threshold of audio panel.
  13. Replies
    3
    Views
    1,363

    I have the remote PS Engineering pac15ex with the...

    I have the remote PS Engineering pac15ex with the audio input to either 1,2, or 4– not sure at this time but it’s an unswitched input to the audio panel. I know I didn’t tie it to 3 since that one...
  14. Replies
    3
    Views
    1,363

    Audio annunciations cut out midsentence

    This has been going on for a while with my 5600 and current software and have been trying to see diagnosable patterns but haven’t been able to. The aural annunciations cut out mid sentence...
  15. Replies
    1
    Views
    1,441

    Earthx battery monitoring thru efis

    Recently installed the earthx battery with fault line wired to input to efis. During a recent fault the warning came on the screen but it doesn’t flash according to a logical code to interpret what...
  16. Recently did the ifr checkride in my rv10 3...

    Recently did the ifr checkride in my rv10 3 screen afs system. Examiner was ok with allowing only map page on pfd and efis on mfd center screen. That allowed non-precision approach to be performed...
  17. Replies
    3
    Views
    1,628

    By chance found a defective bnc connection at nav...

    By chance found a defective bnc connection at nav radio input. Was a strand of ground cable caught between crimp ring and center conductor intermittently shorting. Must have been a late night...
  18. Replies
    3
    Views
    1,628

    Only checking connectors, maybe where the problem...

    Only checking connectors, maybe where the problem lies.
  19. Replies
    9
    Views
    3,467

    I will have to verify if it actually switches to...

    I will have to verify if it actually switches to next airport app plate according to flight plan but know if you select direct to airport it will show up.
  20. Replies
    9
    Views
    3,467

    No I set direct to on ifd then it shows up in...

    No I set direct to on ifd then it shows up in flight plan on 5600 so it should be the airport in cue for approach plate.
  21. Replies
    9
    Views
    3,467

    Ok I see what you’re saying, I was thinking...

    Ok I see what you’re saying, I was thinking something else. I know if I select direct to an airport, then select plates on my 5600 the plates for that airport will be selectable. Do you select...
  22. Replies
    9
    Views
    3,467

    I didn’t know the IFD would cue the plates for...

    I didn’t know the IFD would cue the plates for the 5000 series, how are you getting that to happen, I don’t have that feature now, can you share settings?
  23. Replies
    3
    Views
    1,628

    Remote nav lost glideslope

    I have the Val nav2kr remote nav receiver as a nav source for my 5600, use it as backup or secondary for vor and ils approaches but recently have lost glideslope on an ils approach. Seems to have...
  24. Replies
    4
    Views
    5,299

    What do you have the max airspeed set to?

    What do you have the max airspeed set to?
  25. Thread: Traffic to ipad

    by rvdave
    Replies
    11
    Views
    6,200

    Not sure, maybe Rob will chime in.

    Not sure, maybe Rob will chime in.
Results 1 to 25 of 210
Page 1 of 9 1 2 3 4