Search:

Type: Posts; User: Rob Hickman

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Email me the serial number of the unit and I will...

    Email me the serial number of the unit and I will send you the factory calibration values.

    Rob@Advanced-Flight-Systems.com
  2. Replies
    1
    Views
    385

    It does have some hardware and software...

    It does have some hardware and software filtering, I don't think it is 3-5 seconds. Have you tried it with a heat gun on the probe?
  3. Replies
    2
    Views
    577

    1. Where is backvolts measuring voltage? Given my...

    1. Where is backvolts measuring voltage? Given my configuration this information is not displayed on the EFIS, at what point do I become concerned by its values?

    It it is the voltage of the backup...
  4. Do you have the amp shunt sensor or hall sensor?...

    Do you have the amp shunt sensor or hall sensor?

    Did you change any wiring or literally only installed a new battery?

    Did you change any settings?

    This sounds like you have the amps...
  5. Replies
    1
    Views
    346

    We have a demo mode that we use for shows, ...

    We have a demo mode that we use for shows, currently it is pretty complicated to make it work. I will see what it would take to make an easy demo mode that you could use.
  6. Replies
    2
    Views
    625

    Should be up:...

    Should be up:
    https://www.advancedflightsystems.com/
  7. Replies
    7
    Views
    1,157

    With a Canard aircraft I would use the external...

    With a Canard aircraft I would use the external SV-EMS and mount it near the engine.

    You purchased a Dynon SV-EMS-220 with the Dynon sensor kit so you are good to go.
  8. Replies
    11
    Views
    2,345

    1. are you positive you are running efis software...

    1. are you positive you are running efis software version: Vx15.01.19
    2. What AP are you running on the iPad and are you sure it is not getting weather from a internet connection before you take...
  9. Replies
    7
    Views
    1,157

    If you have the internal EMS board the dynon CHT...

    If you have the internal EMS board the dynon CHT and EGT probes will not work, who told you we can't supply the old sensor kit?

    1. Is fuel flow required to determine percent power? Yes and we...
  10. Check the following: 1. You must have the...

    Check the following:

    1. You must have the Dynon SV-ARINC module, the AF-ARINC module does not get the hold data.
    2. You need the current software on the EFIS
    3. Verify that you have the correct...
  11. Replies
    11
    Views
    2,345

    Local weather is on a 5 minute update rate and...

    Local weather is on a 5 minute update rate and Conus is 15 minutes. The update rate on any device connected to the uavionics should be the same, are you sure you have the baud rate set to 115K?
  12. Replies
    1
    Views
    344

    The 4500 does not display trim commands, only the...

    The 4500 does not display trim commands, only the AF-5000 systems support it. It should show on the Trutrak head.
  13. We are close to releasing a new software release...

    We are close to releasing a new software release that makes the AF-5000 EFIS work with all the same chart data that the Dynon Skyview can use for Europe.
  14. Replies
    11
    Views
    2,345

    We did find a problem with the CONUS weather and...

    We did find a problem with the CONUS weather and we have a new software update that solves the CONUS. We have not had any report of ADSB local weather problems using our Dynon 472 ADSB receiver.
  15. Replies
    14
    Views
    8,708

    All you need to do is connect the wire from the...

    All you need to do is connect the wire from the earthX battery to a spare EFIS digital input.
  16. Replies
    1
    Views
    718

    We have a software fix that enables the XM volume...

    We have a software fix that enables the XM volume adjustment from the AF-5400.
  17. Replies
    1
    Views
    615

    It should not be "red flagged" if you lose the...

    It should not be "red flagged" if you lose the GPS source. On power up the Transponder should be in ALT mode until you get a valid GPS position and then it should be in GND mode until you takeoff. ...
  18. Replies
    15
    Views
    4,004

    We have been extremely busy and we are currently...

    We have been extremely busy and we are currently trying to hire more people. Our sales were way up last year and in the first 6 months of this year our sales are up over 50% so we are trying to...
  19. Replies
    15
    Views
    4,004

    The email on June 2 said "So I believed that it...

    The email on June 2 said "So I believed that it was taking a charge. Sorry for the confusion." So I did not realize you still needed help?

    -Rob Hickman
  20. Replies
    15
    Views
    4,004

    Byron, We show you filled out the form on May...

    Byron,

    We show you filled out the form on May 9th at 11:28AM and Don responded on May 10th at 3:38pm

    Have you checked your SPAM folder?
  21. You can't change it.

    You can't change it.
  22. Replies
    1
    Views
    1,231

    It is either the wiring or a bad sensor. Check...

    It is either the wiring or a bad sensor. Check the voltage on the signal wire, should be around 4+ volts
  23. Replies
    2
    Views
    1,305

    We have a number of people with it connected to...

    We have a number of people with it connected to an EFIS digital input, I have it in both of my planes.
  24. Replies
    15
    Views
    4,004

    The best way to contact us is to email...

    The best way to contact us is to email support@Advanced-Flight-Systems.com
  25. Replies
    15
    Views
    4,004

    When did you post on the contact form and under...

    When did you post on the contact form and under what name?
    I will see if our IT People can figure it out
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4