Search:

Type: Posts; User: ricgc

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    16,655

    Yes we went through that. Battery was fine, but...

    Yes we went through that. Battery was fine, but replaced and went through all the replacement procedure. Have sent you software from my 3500 as well as tried using your software to put key code in....
  2. Replies
    5
    Views
    16,655

    I haven't had any more responses on how to get...

    I haven't had any more responses on how to get unlock code to unlock AOA, if anyone else has a solution please send it to me. Unlock code allows AOA to show up on screen randomly but it does not work...
  3. Replies
    5
    Views
    16,655

    Thanks, thats exactly what I wanted to know. Ric

    Thanks, thats exactly what I wanted to know.
    Ric
  4. Replies
    5
    Views
    16,655

    3500 non s, pitot AOA

    I have just purchased the unlock for 3500, and am not sure if I have to use original ports on each side of the wing or can I use the pitot aoa? If i can use the pitot do I have to t the top wing port...
  5. Replies
    3
    Views
    13,844

    Called today for help. It turned out to be a...

    Called today for help. It turned out to be a loose cable inside.
    Thanks for your steering me in right direction.
    Ric
  6. Replies
    3
    Views
    13,844

    3500 screen blank

    My screen has randam pixels going across screen after leaving master on to charge internal battery for 1/2 hour. Is there a way to reset the unit or does it have to be sent back? Checked voltage of...
  7. Replies
    8
    Views
    16,389

    No, my plane is not a 2 week to taxi plane. It...

    No, my plane is not a 2 week to taxi plane. It simply said check gear. There may be a new warning system coming out from whipair that will detect type of landing which will be a better solution...
  8. Replies
    8
    Views
    16,389

    I have a micro switch controlled by my flap...

    I have a micro switch controlled by my flap lever. It used to say check gear when I put my flaps on which are used for takeoff and landing on the Sportsman so it worked as a great reminder, as I...
  9. Replies
    8
    Views
    16,389

    checked through these 17 files and there doesn't...

    checked through these 17 files and there doesn't appear to be a check gear voice warning any more?
  10. Replies
    8
    Views
    16,389

    found the files but will they work with a non S...

    found the files but will they work with a non S CPU
  11. Replies
    8
    Views
    16,389

    Voice for Gear Warning

    I had my 3500 repaired a couple years ago and I think I lost my voice gear warning at that time. I can only get it to beap for a warning now. I am flying a Glasair Sportsman amphib and gear down in...
  12. Replies
    7
    Views
    11,206

    To bring this thread to a conclusion, and to help...

    To bring this thread to a conclusion, and to help anyone that ends up having the same problem, it turned out to be the AFS 3500. It was a problem they had never seen before, and after sending it back...
  13. Replies
    7
    Views
    11,206

    No, I just have one tach wire hooked up at a...

    No, I just have one tach wire hooked up at a time.
    I will give you a call.
    Ric
  14. Replies
    7
    Views
    11,206

    Yes, I have tried both Pmags with the same...

    Yes, I have tried both Pmags with the same results and tried turning them off one at a time as well with no change. I should double check, the capacitor value is .47uf 50V and a 500 ohm resistor. The...
  15. Replies
    7
    Views
    11,206

    I received your email, but it discusses mags not...

    I received your email, but it discusses mags not P mags. I tried the filter with no luck. The email dicusses the mag sensor, but I am using pin 33 for an electonic ignition with 12v tach signal. I...
  16. Replies
    7
    Views
    11,206

    AFS 3500 rpm drift

    I just installed 2 Pmags. The rpm at medium to higher rpm is drifting up an down 200 rpm from what it really is. The engine is running very smooth and the AFS worked fine prior to switching to Pmags....
Results 1 to 16 of 16