Search:

Type: Posts; User: Jonathon

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    8,841

    Colin, SkyView vector map data, which includes...

    Colin,
    SkyView vector map data, which includes the Airmate product, will be supported in AFS V17 software. The code is mostly now complete, but it is going to require significant flight testing...
  2. Replies
    2
    Views
    226

    Not possible to tee the same float sensors...

    Not possible to tee the same float sensors between two separate display systems. You must wire the sender to the EFIS / EMS-220 or to your old needle gauges, but not to both.
  3. Replies
    2
    Views
    186

    This is not an alternative means to the same end;...

    This is not an alternative means to the same end; both steps are always necessary, in sequential order.

    Holding down the lower rightmost button takes a screenshot, and saves it to the internal...
  4. Thread: GPS Antenna

    by Jonathon
    Replies
    2
    Views
    294

    https://www.rami.com/product/av-801_waas-gps/

    https://www.rami.com/product/av-801_waas-gps/
  5. Replies
    1
    Views
    559

    AF-4500 cannot send NMEA out, only aviation...

    AF-4500 cannot send NMEA out, only aviation format. An Artex ELT can accept aviation format but I don't think an ACK 406 can. Probably going to need a dedicated puck for this one. Sure go ahead...
  6. Replies
    3
    Views
    1,198

    While uAvionix provided engineering and...

    While uAvionix provided engineering and technological assistance to the development of the SV-ADSB-472, it is our product, and it is our firmware code. The firmware updater code has been written and...
  7. Replies
    3
    Views
    1,198

    Not yet, but exactly such an ADSB firmware...

    Not yet, but exactly such an ADSB firmware updater is being actively developed for the AF-5/6000 platform.
  8. Replies
    1
    Views
    512

    No, it does not.

    No, it does not.
  9. Replies
    3
    Views
    924

    No. Only later baseboard revisions noted as such...

    No. Only later baseboard revisions noted as such were designed for both 12V and 24V operation.



    Precision CDI + GS/VDI will work with all modern IFR navigators (GTN650, 750, IFD440, IFD540,...
  10. SET --> CAL (hold 2s) --> G-Meter. Make sure...

    SET --> CAL (hold 2s) --> G-Meter. Make sure Instrument OFF/ON is set to TAPE ONLY, TAPE & POPUP, or POPUP ONLY

    G tape, if enabled, will always display to the left side of the airspeed tape.

    G...
  11. Replies
    1
    Views
    2,091

    on your PFD screen go to SET --> CAL --> Inputs. ...

    on your PFD screen go to SET --> CAL --> Inputs. Change the INPUT 3 usage to NONE. SAVE and BACK out of the cal screen.
  12. The AF ARINC adapter predates the entire SkyView...

    The AF ARINC adapter predates the entire SkyView Network as a standard, and communicates with the EFIS instead via RS-232. Three of the no longer used pins as per the above conversion table are for...
  13. Replies
    5
    Views
    1,992

    Hal, that is the expectation for sure. Not sure...

    Hal, that is the expectation for sure. Not sure why it isn't activating the next leg as you fly through the waypoint.

    We'd like to see what you're seeing here, so if it's not too much trouble,...
  14. Replies
    1
    Views
    1,030

    Dimmer is manual control through the EFIS, we do...

    Dimmer is manual control through the EFIS, we do not support dimming through external controls.

    To adjust brightness, press the CHECK button to pull up the checklist, then twist the topmost knob...
  15. Yes the SV-ARINC will draw holds and yes it will...

    Yes the SV-ARINC will draw holds and yes it will send label 204 baro alt to the navigator.

    Upgrade is fairly simple, make sure you have a free port on your SV-Network hub you can plug the...
  16. Replies
    1
    Views
    2,742

    Gone but not forgotten. We sell replacement...

    Gone but not forgotten. We sell replacement Crossbow remote magnetometers for $150. Call our sales line next week and we can set you up, thanks.
  17. Replies
    1
    Views
    915

    Check that the ethernet cable is plugged in to...

    Check that the ethernet cable is plugged in to the back of each screen. If you still can't see engine data on the MFD take pictures of both displays' SET --> CAL (hold 2s) --> Admin Settings page,...
  18. Replies
    2
    Views
    1,311

    This is coming from the ADSB receiver.

    This is coming from the ADSB receiver.
  19. Replies
    5
    Views
    1,992

    HITS boxes for the active flight plan leg are...

    HITS boxes for the active flight plan leg are pink, and HITS boxes for nonactive legs on the flight plan are purple. If you are seeing the darker HITS boxes on subsequent flight plan legs it is...
  20. Replies
    16
    Views
    5,039

    The ARINC speed change is relevant to all AFS...

    The ARINC speed change is relevant to all AFS EFIS displays with SV-ARINC or ACM ARINC adapters from 16.10.25 software going forward. This is a one and done configuration change, so if you are...
  21. Replies
    16
    Views
    5,039

    Did you update the software on both EFIS displays...

    Did you update the software on both EFIS displays or just one? Is your ethernet cable plugged in and ethernet connection working? Easiest way to check the network is to adjust the baro bug and see...
  22. Replies
    2
    Views
    1,020

    Suggest we move this conversation to a forum...

    Suggest we move this conversation to a forum better able to handle rich content. Email support@advanced-flight-systems.com screenshots of the following EFIS pages:

    CHECK --> ABOUT
    SET --> CAL...
  23. Thread: PFD backup?

    by Jonathon
    Replies
    5
    Views
    1,112

    We are no longer installing internal engine...

    We are no longer installing internal engine boards in EFIS displays. If your other displays are also AF-5000 touchscreen models, then the solution is to upgrade to the SV-EMS-220 and have an engine...
  24. Replies
    1
    Views
    742

    Hello email us the lat/lon for each runway...

    Hello email us the lat/lon for each runway threshold and the lat/lon for the end of each displaced threshold and we will add it into the AFS map, thanks.
  25. Replies
    2
    Views
    866

    Will not hurt anything, but it's possible for the...

    Will not hurt anything, but it's possible for the servos to not be available when you want to use them if you have the switch powered off at system startup. The servos need power always available so...
Results 1 to 25 of 225
Page 1 of 9 1 2 3 4