Search:

Type: Posts; User: Blain

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    175

    Standby frequencies from 4500 to GTR 200

    Very little information describing how this should be configured. Just replaced an Icom A210 with GTR 200. Havern't found standby frequencies on either. I won't rule out a wiring issue.

    When does...
  2. Replies
    2
    Views
    1,774

    I’ve seen them twice. Next time up I’ll go over...

    I’ve seen them twice. Next time up I’ll go over the area. Can the 4500 save a screen shot?
  3. Replies
    2
    Views
    1,774

    Help with icon identification

    AFS 4500 with Uavionix. Noticed an icon that I don’t see in the users manual. It is a yellow ring maybe 1000’ in diameter. Not a yellow circle as only the boarder is yellow. Next to it is “SFC 15...
  4. Replies
    1
    Views
    1,150

    Filter or declutter

    Uavionix Echo into AFS4500. Any way to filter traffic? If I’m at 2500 and can see an airliner at FL 30 it is a distraction.
  5. Thread: AF-4500 FIS-B

    by Blain
    Replies
    3
    Views
    3,200

    I’ve done that. I get traffic but not showing...

    I’ve done that. I get traffic but not showing weather.
  6. Thread: AF-4500 FIS-B

    by Blain
    Replies
    3
    Views
    3,200

    AF-4500 FIS-B

    Should FIS-B display on my 4500 now?
  7. Thread: What is updated?

    by Blain
    Replies
    1
    Views
    3,191

    What is updated?

    I use the free update of aviation and obstacle database for my 4500. I always assumed it was the same updates as a sectional provides. Am I correct?
  8. Replies
    11
    Views
    9,642

    Verified. My report came back clean. And my N...

    Verified. My report came back clean. And my N numbers shows on the ghost.
  9. Replies
    11
    Views
    9,642

    Working with good performance report. But I’m...

    Working with good performance report. But I’m ghosting or seeing myself. Uavionics says I need to make sure my N number is programmed into the EFIS because that’s where the filtering takes place. I...
  10. Replies
    11
    Views
    9,642

    Installed EchoUAT, 4500, serial #3, pin #5, set...

    Installed EchoUAT, 4500, serial #3, pin #5, set serial as ADSB 115k, traffic displays on IPad. “About” shows (PID:0) Idle, TRFC:0, FIS-B:0, OSHIP:0
    Might be source config. Should it be GDL90 or...
  11. Thread: GPS source

    by Blain
    Replies
    1
    Views
    2,571

    GPS source

    Is the 73102 a compliant source for ADSB?
  12. Replies
    3
    Views
    3,520

    Any replacement options for Navworx on 4500?

    Prewired my 4500 for Navworx before the recent fiasco. Not sure I want to wait it out. I see a lot of new hardware in the market. Anything give us in and out in the same format Navworx offered?
  13. Replies
    13
    Views
    18,857

    The default preload for my RV-8 feels better then...

    The default preload for my RV-8 feels better then after the calibration. How can I load the settings listed above to get back to the factory configuration?
  14. Replies
    2
    Views
    3,926

    Saved me a lot of extra work. Thanks Shawn.

    Saved me a lot of extra work. Thanks Shawn.
  15. Replies
    2
    Views
    3,926

    4500 engine sensor harness

    Installing engine sensor harness. I did not group sensor wires with their respective ground terminals. Are all the grounds common or will I need to sort them out?
  16. Thread: wifi connection

    by Blain
    Replies
    3
    Views
    3,936

    Can this be used with the 4500?

    Can this be used with the 4500?
  17. Replies
    2
    Views
    4,898

    Thanks, Shawn. I'll verify they use the same.

    Thanks, Shawn. I'll verify they use the same.
  18. Replies
    2
    Views
    4,898

    Shunt interchange

    Have shunt used on Vans analog amp meter gage. Does it have the right value for my AFS 4500?
  19. Replies
    4
    Views
    6,663

    Just to verify, I'm removing a Insight-GEM 602...

    Just to verify, I'm removing a Insight-GEM 602 engine monitor and replacing with AFS 4500. GEM says they use Type "K for EGT and type "J" for CHT. The thermocouple will be compatible, correct?
  20. Replies
    1
    Views
    2,972

    Found it. Broken d-sub pin #19. Hope there aren't...

    Found it. Broken d-sub pin #19. Hope there aren't any more.
  21. Replies
    1
    Views
    2,972

    Pressure alt to GTX327

    4500 serial #2 out as ICARUS via pin 13, GTX receiving on pin #19, ch #1 set as Icarus. Alt displaying on EFIS not on GTX. All grounds to common field of tabs.

    Before I pull panel to check wiring...
  22. Replies
    3
    Views
    5,254

    Eliminate another puck.

    Eliminate another puck.
  23. Thread: Verify pin-out

    by Blain
    Replies
    5
    Views
    5,854

    Use serial data? TXD and RXD?

    Use serial data? TXD and RXD?
  24. Replies
    3
    Views
    5,254

    Split feed from GPS puck to Navworx

    Using the Dynon puck to feed GPS to the AFS 4500. Can the signal be split to feed both the 4500 and the Navworx ADS600-b?
  25. Thread: Verify pin-out

    by Blain
    Replies
    5
    Views
    5,854

    Thanks Shawn, that answers the Navworks...

    Thanks Shawn, that answers the Navworks connection. What about the comm freq feed?
Results 1 to 25 of 28
Page 1 of 2 1 2