Search:

Type: Posts; User: capdave

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,021

    Autopilot suddenly will not hold altitude.

    Hello,

    With no warning signs our autopilot will not hold altitude. I have checked all of the connections, and all seem ok. Any ideas as to what to check or where to start troubleshooting?
  2. Replies
    1
    Views
    5,054

    Cabin Light ECB?

    Hello,
    I just installed some general downlighting under the glareshield and wired it into the "cabin Lights " circuit. The lights are on a switched rheostat dimmer (the kind that clicks off at full...
  3. Replies
    2
    Views
    3,768

    Hi Jonathon, Thanks for the quick reply. I found...

    Hi Jonathon,
    Thanks for the quick reply. I found the up/down buttons on the bottom check-elec page to be backwards. So I reversed the polarity setting in the software and reversed the wires in the...
  4. Replies
    2
    Views
    3,768

    Flap Position programming trouble

    Hello,
    I have just installed the ray allen pos-12 position indicator on an Rv-10 with AF-5600. The adval numbers on the top right of the screen are changing as expected with flap movement, however,...
  5. Thank you! That makes sense now......

    Thank you! That makes sense now......
  6. Replies
    15
    Views
    171,686

    Hi, Ok thanks ...will do. I think that...

    Hi,
    Ok thanks ...will do. I think that everything is working corrctly now except for a crossed out tis-b message at the top of the ifd display. Is this normal?
  7. Hello, So if the charts on the IFD-540 are not...

    Hello,
    So if the charts on the IFD-540 are not current, how does it interface with the seattle avionics charts so that you can legally fly an ifr approach? Do you not have to select an approach in...
  8. Replies
    15
    Views
    171,686

    Thank you! I will take a look at these settings...

    Thank you! I will take a look at these settings tomorrow when we fly.
  9. Replies
    15
    Views
    171,686

    Thanks! Id appreciate it.

    Thanks! Id appreciate it.
  10. Replies
    15
    Views
    171,686

    Hi, Thanks for the response. Is there any way...

    Hi,
    Thanks for the response. Is there any way that you can post your ifd dat settings as well as your serial port settings ifd on the asvanced screens? I know that the wiring is correct...I'm sure...
  11. Replies
    15
    Views
    171,686

    ADSB Targets on the Avidyne IFD-540

    Hello all,
    Am I supposed to be getting ADSB targets displaying on the avidyne screen as well? I have configured everything to the latest software and adsb works great on the 5600 screens. I get a...
  12. Replies
    3
    Views
    4,680

    No Clock setting

    There is no option to set the clock., only the GMT time offset. It needs to sync with the GPS
  13. Replies
    3
    Views
    4,680

    GPS clock not syncing.

    Hi,
    Both of our 5600 efis screens Zulu times are not syncing to the avidyne gps, and both seem to be different between the two screens as well. The "net sync" button does nothing and is not green...
  14. Replies
    4
    Views
    12,518

    Thank you!

    Thank you!
  15. Replies
    4
    Views
    12,518

    Hi, This is an AF-5000 with the ECB ACM. Yes,...

    Hi,
    This is an AF-5000 with the ECB ACM.
    Yes, all we are trying to do is measure the second battery. What pin of what connector does this tie into?
    Thanks!
  16. Replies
    4
    Views
    12,518

    Secondary ships battery monitor

    Hello,
    We are upgrading to the ECB ACM this week because we want the built in backup alternator support. We are flying with an EFII electronic ignition system and its bus manager. i see the pin...
Results 1 to 16 of 16