Search:

Type: Posts; User: molson309

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    21,432

    Thanks - I discovered I did not have the latest...

    Thanks - I discovered I did not have the latest firmware and once I updated it the adsb-115k option appeared. However the 4500 does not seem to see the data. I wired the echouat to the existing...
  2. Replies
    11
    Views
    21,432

    I asked this question on another thread, so...

    I asked this question on another thread, so ignore if you've already answered: My 4500 only has "ADSB/57K" - no adsb/115k option for serial port 3. I believe I have the latest firmware, is there...
  3. Replies
    17
    Views
    119,926

    I've been trying to get an Echo UAT to talk to my...

    I've been trying to get an Echo UAT to talk to my 4500 - as a replacement for a NavWorx box. The output of the echo UAT is GDL-90 and 115k baud. I'm trying to figure out what format to configure in...
  4. Replies
    8
    Views
    12,984

    Thanks Trevor - I looked in the calibration page....

    Thanks Trevor - I looked in the calibration page. Psf is set to 8, but I noticed a new setting: Audio off below 1500 RPM. This must be new, I don't remember configuring it this way. Turning it to...
  5. Replies
    8
    Views
    12,984

    Thanks Trevor - during my stall testing I got to...

    Thanks Trevor - during my stall testing I got to and through the red chevrons (all of them gone). No audio. I think I will reload the sound files just in case I somehow messed up the AOA audio this...
  6. Replies
    8
    Views
    12,984

    Running 8.6.8. Test page plays audio. The audio...

    Running 8.6.8. Test page plays audio. The audio for AOA was turned off in the calibration page, I turned it back on. Now AOA audio setting is always on after power up. Flew stalls, still no audio....
  7. Replies
    26
    Views
    47,781

    Last night I flew east of MSP to about 20nm west...

    Last night I flew east of MSP to about 20nm west of Eau Claire, WI, at about 8500 ft. I lost ADSB about 15 miles from MSP and did not get it back again until I got close to FCM.

    It's somewhat...
  8. Replies
    8
    Views
    12,984

    Thanks for the reply Trevor. Each time I power...

    Thanks for the reply Trevor. Each time I power the unit on I find that in the AOA menu the sound is turned off, even if I enabled it before powering down. I will try the Test Audio page tonight,...
  9. Replies
    26
    Views
    47,781

    I was flying on Saturday and saw 17 targets, so...

    I was flying on Saturday and saw 17 targets, so the 16 limit I saw was a coincidence. I got info from NavWorx that TIS-B is limited to 15 miles, but wasn't certain if that was 15 miles from the...
  10. Replies
    8
    Views
    12,984

    AOA sound missing on 4500

    I recently upgraded my 4500 the the latest version, 8.06.08. Somehow now I am not getting any audio alerts from the AOA. The display works correctly, but no sound. Also, I am finding after powerup...
  11. Replies
    26
    Views
    47,781

    I used serial port #3 for the TIS output. It very...

    I used serial port #3 for the TIS output. It very well could be that there were not more than 16 targets at the time I looked at it. However, I am still puzzled at the lack of range for the traffic....
  12. Replies
    26
    Views
    47,781

    I am seeing the FIS-B data as well. I don't have...

    I am seeing the FIS-B data as well. I don't have a Mode S transponder so all traffic is coming from the NavWorx box. I do not remember what the MAXDIST and MAXALT parameters are set to.
    What seems...
  13. Replies
    26
    Views
    47,781

    Just got ADS-B working w/my 4500

    I have connected a NavWorx box to my 4500. In the Minneapolis area I get TIS-B up to about 30 miles from Minneapolis and after that all the traffic disappears. I'm wondering if this is a problem...
  14. Replies
    3
    Views
    9,471

    I hate to resuscitate old threads, but it seems...

    I hate to resuscitate old threads, but it seems the appropriate place to post this: I ran into a spontaneous reboot on my 4500 this weekend while doing an engine runup. I was changing pages when the...
  15. Replies
    1
    Views
    6,985

    Data Not Available

    I've been having problems getting data logs from my 4500 unit. With the previous software loaded into it, I could dump the data logs, but even with the data dump set to maximum time, it would only...
Results 1 to 15 of 15