Search:

Type: Posts; User: Lagonia

Page 1 of 2 1 2

Search: Search took 0.01 seconds; generated 19 minute(s) ago.

  1. Happens every time. Aircraft was not out of trim....

    Happens every time. Aircraft was not out of trim. We verified that by having the airplane in perfect trim before engaging the autopilot. Tried that numerous times and got the same result.
  2. AFS 3500 altitude bump when shutting off autopilot

    A friend has an RV9A with a single screen AFS 3500 EFIS and an AFS autopilot. When he disconnects his autopilot from the EFIS screen there is a very pronounced altitude bump. But when he disconnects...
  3. Replies
    1
    Views
    6,584

    EGT not indicating until I reach cruise

    This has happened two out of the last three flights. #1 cylinder EGT does not indicate any heat until,I reach cruise altitude. I know the engine is running properly since it is running smooth, CHT is...
  4. But you have a slider. That’s what I have and...

    But you have a slider. That’s what I have and prefer.
  5. I have a 9 with dual AFS 4500 system. Last year...

    I have a 9 with dual AFS 4500 system. Last year we installed the Garmin GPS175. We also purchased the ARINC 429 module. All works without any problems. So yes, the ARINC module does work with a 4500...
  6. Replies
    3
    Views
    19,317

    Thank you.

    Thank you.
  7. Replies
    3
    Views
    19,317

    After a little more investigation I find that my...

    After a little more investigation I find that my system does not have the flap position indicator. I found on page 86 of the AFS manual what piece I need to order from Ray Allen. My question is about...
  8. Replies
    3
    Views
    19,317

    How to set flap position indication

    I have a dual screen 4500. My flap indication always shows full flaps down. How do I calibrate to show proper flap positions?
  9. Replies
    0
    Views
    4,626

    Manifold pressure indication gone

    I have an AFS 4500 with an O-360 engine on my RV9.
    Went flying yesterday and all was good.
    Today on start up I first had an intermittent manifold pressure indication on my EFIS, indication then...
  10. Replies
    3
    Views
    6,369

    That’s a little confusing. Are you saying that...

    That’s a little confusing. Are you saying that when I have my EFIS in Lat Nav, Vertical will automatically switch to Arm? I understand having Lat in Nav to follow the course, not in HDG. But please...
  11. Replies
    3
    Views
    6,369

    Flying an LPV approach

    When flying an LPV approach do I need to manually switch from Vertical Alt to Vertical Arm or will my 4500 switch automatically?
  12. Replies
    2
    Views
    6,680

    Thank you Shawn. Will check that out tomorrow.

    Thank you Shawn. Will check that out tomorrow.
  13. Replies
    2
    Views
    6,680

    How to check oil temp sensor

    On my last flight the oil temp registered between 117-134F. It was during a three hour cross country flight. Previous flight was 2.5 hours and oil temp was right below 180F. Before I install an oil...
  14. Replies
    4
    Views
    49,892

    I do,have two questions. I have SV on my PFD...

    I do,have two questions.
    I have SV on my PFD but not on the MFD so I do not get terrain alerts, red, on my MFD which is used for my navigation map. What do I need to install to get terrain info on...
  15. Replies
    4
    Views
    49,892

    Don’t have any bugs that I know of. Just asking...

    Don’t have any bugs that I know of. Just asking if AFS will be adding any features for legacy units, I have dual 4500’s, like you folks do for the latest 5000 series units.
  16. Replies
    4
    Views
    49,892

    Software updates for legacy units?

    I understand your focus on the AF-5600 units but is there any chance you will offer software updates for the AF-4500 series? I
  17. Thread: ADS-B for 4500

    by Lagonia
    Replies
    17
    Views
    119,864

    Would the GDL-52 R work for ADS-B in with the...

    Would the GDL-52 R work for ADS-B in with the AF-4500? Right now I
  18. Replies
    9
    Views
    107,928

    Shawn, are you saying that on the MFD I now need...

    Shawn, are you saying that on the MFD I now need to change the GPS/NAV Data Source 2 (on the MFD) to Remote Nav?
  19. Replies
    9
    Views
    107,928

    I made the changes to my configuration as you...

    I made the changes to my configuration as you folks suggested to me on a Facebook post. I still have one question. AFS comment said for me to decide how my SL-30 was wired and it should only be...
  20. Replies
    9
    Views
    107,928

    I should add that the SL-30 is wired to the PFD.

    I should add that the SL-30 is wired to the PFD.
  21. Replies
    9
    Views
    107,928

    Thank you Shawn. I do have an AF-ARINC module. ...

    Thank you Shawn. I do have an AF-ARINC module. I think the issue may be the configuration of the Serial Ports. PFD is configured as follows: Port 1 AVTN/AVTN, Port 2 TRFC/ICARUS, Port 3 SL-30, and...
  22. Replies
    9
    Views
    107,928

    I also have the select switch to control the...

    I also have the select switch to control the vizion through the EFIS or the GPS.
  23. Replies
    9
    Views
    107,928

    Configuring the AFS 4500 dual screens

    I have dual AFS 4500 screens.
    I recently installed an ARINC 429, the TruTrak Vizion 385 and a Garmin 175. I am trying to control my autopilot from my EFIS. How should my screens be configured? ...
  24. Replies
    4
    Views
    105,658

    That is great to learn. I would much prefer to...

    That is great to learn. I would much prefer to see my geo referenced plates on my EFIS rather than my iPad.
  25. Replies
    4
    Views
    105,658

    How do you get the geo referenced approach plates...

    How do you get the geo referenced approach plates to show on my 4500? I have been using my iPad with Foreflight but would prefer to see them on my AFS 4500 moving map. I have a Jeppesen...
Results 1 to 25 of 43
Page 1 of 2 1 2