Search:

Type: Posts; User: sahrens

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    4,325

    V16-06-15 and Landing override

    During take-off acceleration the tonal stall warning starts at about 30 KIAS and continues until about 70 KIAS during climb out. I have adjusted Landing Override for the landing sequence and I do...
  2. Replies
    0
    Views
    1,896

    V16-06-15 and Alert Tone Start Bar

    In regard to this information

    "Setting the Alert Tone Start Bar to 16 will cause the AOA tones to start beeping at the normal approach AOA and become a steady tone at the red bar (15% above...
  3. Thread: audio aoa

    by sahrens
    Replies
    19
    Views
    81,025

    Shawn, I can be a beta tester if you need an...

    Shawn, I can be a beta tester if you need an additional user. I'm located in Portland OR area. I have an RV-7 with 5000T EFIS
  4. Replies
    1
    Views
    3,190

    EarthX Temperature

    I have used the carburetor temp probe to monitor the temperature of my EarthX battery. The EFIS displays carb XX for the temperature. Any chance that label could be changed to a user entered four...
  5. Thread: audio aoa

    by sahrens
    Replies
    19
    Views
    81,025

    Any update on the release? I would really like...

    Any update on the release? I would really like to have access to the AOA tones.

    Thank you.

    Scott
  6. Replies
    1
    Views
    40,896

    Modifying AOA data

    Flying an RV-7 and I would like to adjust the AOA settings to increase or decrease when the warnings activate. Is there a value that corresponds to approximately 1 KIAS change? For example my...
  7. Replies
    3
    Views
    71,417

    I spoke with tech support yesterday afternoon and...

    I spoke with tech support yesterday afternoon and learned this will be resolved in an upcoming release.
  8. Replies
    3
    Views
    71,417

    The donut is clearly visible, especially the...

    The donut is clearly visible, especially the green portion. The audio works and is clearly understandable and the flap position indicator is operating normally and clearly visible. The data comes...
  9. Replies
    3
    Views
    71,417

    AOA brightness adjustment

    Is there a method to adjust the brightness of the AOA chevrons? I
  10. Replies
    2
    Views
    35,940

    Thank you!

    Thank you!
  11. Replies
    2
    Views
    35,940

    Backvolts, volts1 & volts2

    I have a 5500T with a TCW 6ah backup battery. When I download the logs the system records three voltages, backvolts, volts 1 and volts 2.

    1. Where is backvolts measuring voltage? Given my...
  12. Replies
    1
    Views
    3,436

    Checklist limits

    Is there a limit to the number of lines within a checklist? I can not get items beyond line 11 on the CHKLST1.LINEn area of the checklist to display (AFS 5500T.) I have recreated the checklist to...
  13. Replies
    1
    Views
    71,200

    5500 and Dynon firmware release

    Dynon released a firmware update for the GPS 2020 to fix the NACv bug on the ADSB report among other issues. When will AFS release that update for the Dynon equipment through the AFS 5500?

    Thanks
  14. Replies
    0
    Views
    52,747

    AF-5500 and TCW drain

    I have a AF-5500 with the TCW backup battery. Recently the TCW battery failed. TCW stated the battery had been discharged to the point of damaging a cell. I had to replace the battery. Other than...
  15. Replies
    2
    Views
    5,166

    Bringing this thread back up. Yesterday I was...

    Bringing this thread back up. Yesterday I was attempting to load flight plans from my iPad mini 4 via Foreflight to my AFS 5500T. I received the same error code on each of several attempts,...
  16. Thread: TFRs

    by sahrens
    Replies
    5
    Views
    10,095

    I flew day and verified that I was receiving...

    I flew day and verified that I was receiving ground station data and could view the TFR text data on the TFR page. What I misunderstood was how the TFR and WX graphic data was displayed. That data...
  17. Thread: TFRs

    by sahrens
    Replies
    5
    Views
    10,095

    Well, I thought I had wx turned on. Now I will...

    Well, I thought I had wx turned on. Now I will have to check it out tomorrow morning. I am getting traffic through ads-b
  18. Thread: TFRs

    by sahrens
    Replies
    5
    Views
    10,095

    TFRs

    I have a 5500T and the Dynon 470. The 5500 is not displaying any TFRs or wx. I am receiving traffic.

    Is this a know software issue?

    Thank you.

    Scott
  19. Replies
    5
    Views
    4,515

    Is it possible to rename the carb temp label that...

    Is it possible to rename the carb temp label that is displayed on the engine screen? I am using it to monitor the battery temp of my EarthX battery, so Batt Temp would be ideal.

    Thank you.
    ...
  20. Replies
    5
    Views
    4,515

    Temperature measurement

    I would like to hook a J or K type thermocouple to the Dynon EMS to monitor my EarthX battery temperature. The battery is located on the firewall in the standard location for a Vans RV-7.

    1. May...
  21. Replies
    1
    Views
    4,612

    5500T data logs

    I have my main buss connected to the SV-EMS pin 1 to measure alternator/battery voltage into the aircraft. I connected the IBBS battery information to pin 13 on the EFIS expansion plug. When I pull...
  22. Replies
    4
    Views
    9,533

    Thank you for that clarification. Scott

    Thank you for that clarification.

    Scott
  23. Replies
    4
    Views
    9,533

    Just to make sure we are on the same page, the...

    Just to make sure we are on the same page, the sum of the SV device's demand is 0.83A. The devices in my installation so far are:

    These two always get power from the EFIS
    GPS-2020 0.10A
    WIFI...
  24. Replies
    4
    Views
    9,533

    EFIS and TCWTECH battery

    I am installing a 5500 in my RV-7 panel connecting to Dynon SV-Network devices. The sum of the power demands for the Dynon devices connected to the SV-Network exceeds the 3.5 amp limitation of the...
  25. Replies
    8
    Views
    10,922

    Remote comm installation

    Does the remote comm radio require the connection of the panel control head? I would like to install the radio and control it through either EFIS without the panel control head.

    Thanks
Results 1 to 25 of 25