Search:

Type: Posts; User: Don Patterson

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    3,724

    wifi connection

    Will the new 73140 Wi-Fi Module connect to an ipad running Foreflight, and transfer flight planning information into the 5600?

    Don
  2. Replies
    1
    Views
    2,539

    Kavlico sensors on 3400 EM

    I removed my VDO oil and fuel sensors and installed the new Kavlico 3 wire sensors per the electrical print for my 3400 EM. I turned my boost pump on for a couple seconds and it went over 1200 psi...
  3. Replies
    6
    Views
    3,979

    Shawn, Thanks again for your help. Don

    Shawn,

    Thanks again for your help.

    Don
  4. Replies
    6
    Views
    3,979

    I’m upgrading my 4500 to a 5600 EFIS and will be...

    I’m upgrading my 4500 to a 5600 EFIS and will be using a 496 for GPS navigation.
    Because the AF-Pilot and my Arinc429 all get interconnected with the 5600, I had a few questions on the proper...
  5. Replies
    6
    Views
    3,979

    Rob, The 496 GPS OUT (TX) should be...

    Rob,


    The 496 GPS OUT (TX) should be connected only to one of the EFIS serial port RX lines.

    1. Can I use a (TX) serial port on another screen? My 3400 EM serial port 1 has nothing connected...
  6. Replies
    6
    Views
    3,979

    Upgrade from the 4500 to 5600

    On the 5600 PFD I am using a 496 for GPS navigation, and the AF-Pilot autopilot. I also have an Arinc429 that is all to be interconnected with the GPS data to get full functionality out of my 5600. ...
  7. Replies
    3
    Views
    2,935

    Will the backup battery in the TCW show as it has...

    Will the backup battery in the TCW show as it has on my 4500 with the built in battery?
  8. Replies
    3
    Views
    2,935

    TCW battery backup connections.

    I am in the planing stages of upgrading my 4500 to the 5600. The 6 amp TCW battery backup system shows a connection on terminal 2 for Batt-info. Where on the 5600 would I connect terminal 2 from the...
  9. Replies
    4
    Views
    4,284

    I have the NavWorx system in my plane and I added...

    I have the NavWorx system in my plane and I added the display of traffic to a Garmin 496 that I have mounted in the panel. The 496 adds audio annunciation into my audio panel and I get audio warnings...
  10. Thread: Afs 5400

    by Don Patterson
    Replies
    8
    Views
    6,059

    5600 upgrade

    I also have a 4500 and would like to upgrade to the 5600 but have a few questions.
    I understand the upgrade requires the installation of an external AHRS that is presently in my 4500.
    My...
  11. Replies
    3
    Views
    2,983

    Thanks Rob.

    Thanks Rob.
  12. Replies
    3
    Views
    2,983

    Identifying an intersection

    While flying along an airway I occasionally need to identify my location with a cross radial from another VOR.
    What would be the best method on my 4500 to ID this location.
    I am using an SL 30...
  13. Replies
    1
    Views
    2,156

    Battery problem

    My battery in our plane failed to start the plane after arriving to my home field from a 20 hour cross country. After testing the starting system I found the 1 year old Odyssey battery had 12 volts...
  14. Replies
    16
    Views
    8,427

    Chardks, My fuel flow servo is mounted mid point...

    Chardks,
    My fuel flow servo is mounted mid point between the Bendix fuel injection servo
    and the distribution spider as you recommended. However it's mounted to a bracket
    that is then held in...
  15. Replies
    16
    Views
    8,427

    chardks, My Lycoming engine is equipped with a...

    chardks,
    My Lycoming engine is equipped with a Bendix fuel injected system. Could the issue I was referring to at the beginning of this thread, be caused by a problem with a fuel injected system....
  16. Replies
    6
    Views
    2,874

    Looking in the manual and found (ARINC Module...

    Looking in the manual and found (ARINC Module Software Updating)

    Should I be updating my 3400 engine monitor with the Arinc software or just my 4500?

    Thanks Rob
  17. Replies
    6
    Views
    2,874

    When updating my 4500 I thought the Arinc...

    When updating my 4500 I thought the Arinc software was included in the
    Download and it would go to the Arinc while updating the 4500.
    Is there another method for updating the Arinc separately?
    Don
  18. Replies
    6
    Views
    2,874

    Rob, I did install the latest software again and...

    Rob,
    I did install the latest software again and after going into the about screen it still shows version 3.7

    Don
  19. Replies
    6
    Views
    2,874

    Arinc update

    Rob
    I saw on my about page of my 4500 that I am running version 3.7
    On my Arinc adaptor. How can I update that to the latest version. On my
    3400 EM it shows not installed.

    Don
  20. Seems a lot of people now are using the ipad for...

    Seems a lot of people now are using the ipad for preflight planing, myself included. I agree with John that it would sure make adding flight plan information a breeze, if it could be added to the...
  21. Replies
    1
    Views
    2,677

    Navworx adsb port settings

    Hi Rob
    I have a 4500 EFIS and a 3400 EM and just installed a New Navworx ADS600-BG.
    The display connections are attached to the 3400 EM serial port 3.
    The altitude encoder is attached to the...
  22. Replies
    16
    Views
    8,427

    A question on leaning with my 3400 EM

    After reaching my cruse altitude I set my power and turn on the peak detect system on my AFS 3400 Engine monitor. As I start leaning, the EGT temps rise until they peak. As I continue to lean the EGT...
  23. Thanks Rob.

    Thanks Rob.
  24. Hi Rob Both the 4500 & 3400 are synthetic. So if...

    Hi Rob
    Both the 4500 & 3400 are synthetic. So if I understand I can just tap into
    The serial port #2 even if my transponder is already using that connection.
    Could the 9 pin connector on my...
  25. ADS600-GB connections to AFS 4500 and AFS 3400.

    Hi Rob, I have the 4500 EFIS and a 3400 EM and will be installing the certified NavWorx ADS600-BG. I have an Arinc 429 connected to the EFIS expansion connector for my AF-Pilot auto pilot. Your 4500...
Results 1 to 25 of 34
Page 1 of 2 1 2