Search:

Type: Posts; User: rshannon

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    9,406

    Finally got this pulled out and on the bench....

    Finally got this pulled out and on the bench. After disconnecting the backup battery, and draining per your suggestion, I'm not able to reload the software. Expect incoming.
  2. Replies
    7
    Views
    13,285

    I have dual 3400s units and unfortunately, in my...

    I have dual 3400s units and unfortunately, in my vertically-challenged Murphy Rebel panel I can't change to the taller 3500/5400 vertical dimension. :(
  3. Replies
    4
    Views
    9,406

    Because getting it out of this panel is quite a...

    Because getting it out of this panel is quite a chore, I may as well try reloading the software first, just in case it might recover by doing that alone. If it doesn't, I'll pull it out and do the...
  4. Replies
    7
    Views
    13,285

    Additionally, will the outboard accessories I...

    Additionally, will the outboard accessories I already have with my 3500s series work with the 5400? Such as the AHRS, ARINC, OAT, AF-GPS, engine sensors and AOA (wing install)?
  5. Replies
    7
    Views
    13,285

    AF-5400 dimensions

    On the AF-5000 series product page the link to dimensions for the AF-5400 leads to a drawing of dimensions for the AF-3500. Is that an error, or are the AF-5400 dimensions identical to the AF-3500,...
  6. Replies
    4
    Views
    9,406

    3400s shutdown fault

    My 3400s EF, which along with the EE has performed flawlessly for almost 5 years, suddenly refused to shut down. Instead, it displayed a set of 5-6 character (text) lines including:

    "INFO: RCU not...
  7. Replies
    5
    Views
    10,574

    Thanks, Rob. I've successfully restored the file...

    Thanks, Rob. I've successfully restored the file you emailed, confirmed in the oil pressure config. Will report results when I've had a chance to run the engine.

    (BTW, I misstated the ver. upgrade...
  8. Replies
    5
    Views
    10,574

    VDO 360-001 oil pressure sender

    I have a VDO 360-001 0-80 PSI, 5 bar, 10-180 ohms oil pressure sender for my Jabiru 3300, which has started showing at least double the oil pressure it previously reported correctly during the first...
  9. Replies
    14
    Views
    22,160

    Hmm. With jumpers, I tried swapping the senders...

    Hmm. With jumpers, I tried swapping the senders from their normal EFIS tank circuit to the opposite EFIS tank circuit, one at a time. I'm getting very different results -- still erroneous -- when...
  10. Replies
    14
    Views
    22,160

    According to the invoice sent to the orig....

    According to the invoice sent to the orig. builder, I have Westberg 395-5SB5 senders, which are described as "Capacitance Fuel Level Sender...240 ohm, 12VDC." (I've left out a couple physical size...
  11. Replies
    14
    Views
    22,160

    Trying to diagnose new problems with my Westach...

    Trying to diagnose new problems with my Westach gauges, which worked fine for over 160 hrs. Is the zero figure given above meant to be with power and ground connected to the gauge sender, just not...
  12. Replies
    3
    Views
    8,522

    Thanks. What is bank angle mode? The manual...

    Thanks. What is bank angle mode? The manual doesn't mention it, per se. Is it wing leveling only, or ...?
  13. Replies
    3
    Views
    8,522

    GPS serial data fault indication?

    1) If the AF-Pilot is not getting good serial data from the GPS on pin 17, will it display any error or fault message?

    2) Will AP mode work at all?

    3) My understanding is that the AF-Pilot has...
  14. Replies
    10
    Views
    15,174

    Thanks, Rob. Will there be an upgrade or trade-in...

    Thanks, Rob. Will there be an upgrade or trade-in discount for existing 3400s/4500 customers?
  15. Replies
    2
    Views
    7,619

    FWIW, my early-style OAT wires are 24 ga.

    FWIW, my early-style OAT wires are 24 ga.
  16. Replies
    48
    Views
    49,397

    Alan, would appreciate knowing how this issue...

    Alan, would appreciate knowing how this issue worked out for you. Thanks.
  17. Thread: status page

    by rshannon
    Replies
    1
    Views
    6,781

    status page

    I'm trying to read the status data from the XM receiver (which is configured to be online, MASTER/SLAVE) but the CHECK-MAINT-ABOUT status page does not seem to be working properly on either of my two...
  18. Replies
    7
    Views
    34,951

    Very helpful video. Does a tailwheel plane need...

    Very helpful video. Does a tailwheel plane need to be in level flight attitude for this rotation procedure?
  19. Replies
    6
    Views
    12,631

    NavWorx ADS-B w/ARINC

    NavWorx sells their ADS-B transceiver with or without an optional ARINC interface. Are there any plans to utilize ARINC as an alternate method of connecting to AFS EFIS's, i.e., in addition to a...
  20. Replies
    2
    Views
    6,462

    I'd like to join in requesting a timer audio...

    I'd like to join in requesting a timer audio alert. "Check timer" in the headset would be very helpful.
  21. Replies
    1
    Views
    4,747

    If you haven't already, contact Tech Support. I...

    If you haven't already, contact Tech Support. I had a similar problem, though with a different sensor system (Jabiru PM alternator pickup) and the tech support staff was helpful and persistent in...
  22. Thread: Wish list

    by rshannon
    Replies
    29
    Views
    38,221

    Jenny should be more informative, progressively...

    Jenny should be more informative, progressively conveying just how badly the PIC is screwing up, like:

    1) Check CHT's.
    2) Hey banana brain, CHT's are still too high!
    3) With CHT's like that,...
  23. Replies
    6
    Views
    8,896

    1) Whew! 2) Jenny's voice and I are well...

    1) Whew!
    2) Jenny's voice and I are well acquainted now and of course, I always take her very seriously -- so that would be fine.
    3) As for investigating things I'm not sure of, I would never have...
  24. Replies
    6
    Views
    8,896

    Yes, I'm running v7.10.24. Do you think the knob...

    Yes, I'm running v7.10.24. Do you think the knob spin routine repaired/reset any damage done by pushing START a few days ago, if any?

    The real problem is that AFS systems and service are...
  25. Replies
    6
    Views
    8,896

    My [ADMINISTRATOR MODE] said it's DISABLED, yet...

    My [ADMINISTRATOR MODE] said it's DISABLED, yet prior to posting this query, it _was_ possible to hit [AIRDATA AUTO-CONFIG][START], even though ADMIN MODE was DISABLED. So I don't understand your...
Results 1 to 25 of 39
Page 1 of 2 1 2