Search:

Type: Posts; User: dnelson

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds; generated 24 minute(s) ago.

  1. Reseated the video connector at the bezel end and...

    Reseated the video connector at the bezel end and all is good!

    As for the SD card problem, I'm just going to buy a new set and see if the problem persists.
  2. Thanks Bob - I just got an email from Shawn. I...

    Thanks Bob - I just got an email from Shawn. I am/was hoping it is/was going to be that simple. I'll keep you all posted.

    /\/elson
  3. Lost weight and balance config and now the screen flickers badly

    Hi AFS,

    I mention the following recent events in case they are somehow related. Until Dec 2017, my 4500EE has been downright stable. Firmware is 8.08.35-MV16 and was updated years ago. I've got...
  4. Replies
    6
    Views
    50,065

    Hi Shawn, Thanks! That's a relief knowing...

    Hi Shawn,

    Thanks! That's a relief knowing what they really are. Contributing to my confusion was that non-active TFRs are also yellow and the effective height labels associated with each drop...
  5. Replies
    6
    Views
    50,065

    Non-existent TFRs being displayed

    Curious if anybody else is seeing, what seems to be, non-existent TFRs on their 4500's. I think I first ran into this shortly after upgrading the 4500's firmware from 8.8.31 to 8.8.35 and the...
  6. Fantastic - Thank you, Shawn.

    Fantastic - Thank you, Shawn.
  7. Thanks Shawn. This seems like an ideal upgrade...

    Thanks Shawn. This seems like an ideal upgrade to perform during my next annual as I believe my screen is just a plain EE.

    ?: Once the conversion is done on the screen, can I still mix-n-match...
  8. What's needed to convert to using Kavlico sensors for a 4500?

    Hi AFS,

    My VDO fuel pressure sensor has, yet again, died.

    What is needed to convert over to a Kavlico setup and the associated costs? I've a single 4500EE s/n 61134.

    Thank you,
    /\/elson
  9. Replies
    10
    Views
    17,999

    Follow-up Results

    To the serial connectivity issues, I've received some updated firmware from Ken@AFS to try out. Need to load/test and provide any feedback.

    To the brief 'UAT Error' alerts, this is a known issue...
  10. Replies
    10
    Views
    17,999

    Hi Rob - Email sent. Hi Bob - Wow, that's one...

    Hi Rob - Email sent.

    Hi Bob - Wow, that's one for the troubleshooting books. When I was configuring the UAT back in November, the 'UAT Console' program would just up and quit if I let it sit for...
  11. Replies
    10
    Views
    17,999

    Hi Bob, > Monitor the OSHIP count. If the...

    Hi Bob,

    > Monitor the OSHIP count. If the counter is increasing, you at least have sucessfull communications between the Navworx unit and the EFIS.

    Great - Thx for that.

    > Unfortunately, the...
  12. Replies
    10
    Views
    17,999

    Hi Larry, As for the 'UAT Error' annc, yes,...

    Hi Larry,

    As for the 'UAT Error' annc, yes, it's P1_14 (pin #14 of the P1 connector) from the UAT to Input_#3 (pin #8 of the 4500's main harness). It will annc (visually and audibly) breifly...
  13. Replies
    10
    Views
    17,999

    Temporary loss of ADS-B

    Hi AFS,

    I'm not entirely sure where to start, with AFS or NavWorx, but I'll start here because of the forum and a few other quirks I've noticed over the last couple of months.

    Back in November...
  14. Hi Rob - Thanks again for calling me this AM and...

    Hi Rob - Thanks again for calling me this AM and walking me through the process.

    As for the "bug report", there are EFIS and EMS display settings under the Map menu tree and this is what was...
  15. I've disabled the EFIS Page and the EFIS Menu Tree - Now what?

    Hi AFS,

    Short Version: I've managed to disable the 'EFIS' page from the 'page list', and subsequently, also the EFIS menu tree. Without the EFIS menu, I can't configure the 'page list'. So, how...
  16. Replies
    3
    Views
    7,331

    Hi AFS, It's been just over a year since the...

    Hi AFS,

    It's been just over a year since the last post. I'm considering ADSB for my 4500-EE. Is this still the case?

    Thank you,
    /\/elson
  17. Hi Chardks, Great - I'll look for the VSR...

    Hi Chardks,



    Great - I'll look for the VSR field.



    Bummer.
  18. Follow up questions ...

    Hi AFS,

    I've been using the VER:FPL mode quite successfully. I've two follow-up questions when you get the chance:

    - First, is there a shortcut method to selecting VER:FPL mode on the 4500? ...
  19. Success

    Hi chardks,

    It worked liked like a charm! My procedure was as follows:

    - Selected Direct-To on the 430 for my destination.
    - Set my ALT bug to my current altitude.
    - Set my MINS bug to 1650'...
  20. Hi Rob, Got some test flights in this weekend....

    Hi Rob,

    Got some test flights in this weekend. I did verify that LAT:NAV and VER:ARM were displayed. Still, the A/P flew right over TOD and kept on flying straight and level. My procedures were...
  21. Hi Rob, Next time I'm up, I'll verify the...

    Hi Rob,

    Next time I'm up, I'll verify the LAT:NAV and VER:ARM. Regarding the entered altitudes on the EFIS, I've set the Minimums bug to pattern altitude and the Altitude bug to my desired...
  22. ping ping (need 10 chars to post)

    ping ping (need 10 chars to post)
  23. Using the TOD and BOD markings for the decent profile

    Hi AFS,

    What do I need to do to get the AP to follow the TOD and BOD decent profile?

    So far, my sequence is as follows: I've entered the flight plan into the GNS-430W, I can see the flight...
  24. Replies
    1
    Views
    5,525

    Extended cernterlines for private airports

    Hi AFS,

    For a 4500EE running 8.8.12 with V16 map data, can extended centerlines be displayed for private airports? I'm not entirely sure if 'extended certerline' is the proper term but I'm...
  25. Replies
    5
    Views
    8,593

    Hi idleup, For an RV-7A tip-up, I couldn't...

    Hi idleup,

    For an RV-7A tip-up, I couldn't find a reasonably nice and convenient place to mount the unit. I ended mounting it to the bottom of the EFIS itself (4500) using two 3/8" wide (I think)...
Results 1 to 25 of 103
Page 1 of 5 1 2 3 4