Finally got this pulled out and on the bench. After disconnecting the backup battery, and draining per your suggestion, I'm not able to reload the software. Expect incoming.
Type: Posts; User: rshannon
Finally got this pulled out and on the bench. After disconnecting the backup battery, and draining per your suggestion, I'm not able to reload the software. Expect incoming.
I have dual 3400s units and unfortunately, in my vertically-challenged Murphy Rebel panel I can't change to the taller 3500/5400 vertical dimension. :(
Because getting it out of this panel is quite a chore, I may as well try reloading the software first, just in case it might recover by doing that alone. If it doesn't, I'll pull it out and do the...
Additionally, will the outboard accessories I already have with my 3500s series work with the 5400? Such as the AHRS, ARINC, OAT, AF-GPS, engine sensors and AOA (wing install)?
On the AF-5000 series product page the link to dimensions for the AF-5400 leads to a drawing of dimensions for the AF-3500. Is that an error, or are the AF-5400 dimensions identical to the AF-3500,...
My 3400s EF, which along with the EE has performed flawlessly for almost 5 years, suddenly refused to shut down. Instead, it displayed a set of 5-6 character (text) lines including:
"INFO: RCU not...
Thanks, Rob. I've successfully restored the file you emailed, confirmed in the oil pressure config. Will report results when I've had a chance to run the engine.
(BTW, I misstated the ver. upgrade...
I have a VDO 360-001 0-80 PSI, 5 bar, 10-180 ohms oil pressure sender for my Jabiru 3300, which has started showing at least double the oil pressure it previously reported correctly during the first...
Hmm. With jumpers, I tried swapping the senders from their normal EFIS tank circuit to the opposite EFIS tank circuit, one at a time. I'm getting very different results -- still erroneous -- when...
According to the invoice sent to the orig. builder, I have Westberg 395-5SB5 senders, which are described as "Capacitance Fuel Level Sender...240 ohm, 12VDC." (I've left out a couple physical size...
Trying to diagnose new problems with my Westach gauges, which worked fine for over 160 hrs. Is the zero figure given above meant to be with power and ground connected to the gauge sender, just not...
Thanks. What is bank angle mode? The manual doesn't mention it, per se. Is it wing leveling only, or ...?
1) If the AF-Pilot is not getting good serial data from the GPS on pin 17, will it display any error or fault message?
2) Will AP mode work at all?
3) My understanding is that the AF-Pilot has...
Thanks, Rob. Will there be an upgrade or trade-in discount for existing 3400s/4500 customers?
FWIW, my early-style OAT wires are 24 ga.
Alan, would appreciate knowing how this issue worked out for you. Thanks.
I'm trying to read the status data from the XM receiver (which is configured to be online, MASTER/SLAVE) but the CHECK-MAINT-ABOUT status page does not seem to be working properly on either of my two...
Very helpful video. Does a tailwheel plane need to be in level flight attitude for this rotation procedure?
NavWorx sells their ADS-B transceiver with or without an optional ARINC interface. Are there any plans to utilize ARINC as an alternate method of connecting to AFS EFIS's, i.e., in addition to a...
I'd like to join in requesting a timer audio alert. "Check timer" in the headset would be very helpful.
If you haven't already, contact Tech Support. I had a similar problem, though with a different sensor system (Jabiru PM alternator pickup) and the tech support staff was helpful and persistent in...
Jenny should be more informative, progressively conveying just how badly the PIC is screwing up, like:
1) Check CHT's.
2) Hey banana brain, CHT's are still too high!
3) With CHT's like that,...
1) Whew!
2) Jenny's voice and I are well acquainted now and of course, I always take her very seriously -- so that would be fine.
3) As for investigating things I'm not sure of, I would never have...
Yes, I'm running v7.10.24. Do you think the knob spin routine repaired/reset any damage done by pushing START a few days ago, if any?
The real problem is that AFS systems and service are...
My [ADMINISTRATOR MODE] said it's DISABLED, yet prior to posting this query, it _was_ possible to hit [AIRDATA AUTO-CONFIG][START], even though ADMIN MODE was DISABLED. So I don't understand your...