Search:

Type: Posts; User: MacCool

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds; generated 53 minute(s) ago.

  1. Replies
    2
    Views
    2,426

    Yes, thanks…so I’ve read here. I’m...

    Yes, thanks…so I’ve read here. I’m troubleshooting non-fluctuating, but low, oil temps, and trying to avoid pulling the vernatherm (awkward location). More than likely the issue is an efficient...
  2. Replies
    2
    Views
    2,426

    Oil temp sensor replacement?

    Is the Dynon 100409-000 oil temperature sensor a suitable replacement for the AFS 40405 on my IO-320D1A and AFS5400 / SV-EMS?
  3. Replies
    2
    Views
    4,920

    OK, that's helpful, thanks. It makes sense...

    OK, that's helpful, thanks. It makes sense because when I got that 5400 from you guys, that number had been set to the airplane's stall speed.
  4. Replies
    2
    Views
    4,920

    Landing warning override ....

    I have an "AFS Pilot" autopilot, which was installed by the builder 10 years ago in conjunction with the AFS4500 with in-wing ports for the AoA system. When the 4500 died, I replaced it with a 5400...
  5. Replies
    2
    Views
    1,633

    Thanks for the reply

    Thanks for the reply
  6. Replies
    2
    Views
    1,633

    Contextual checklist pop-ups

    This is a simple question with a probably-simple answer that I just can’t seem to pull out of the manual.

    On my 5400, I routinely get checklists slide in to the right side of the screen at various...
  7. Replies
    3
    Views
    2,357

    Just an update, as I've had a few queries via PM...

    Just an update, as I've had a few queries via PM from pilots that were having the same or similar problem.

    Regarding most of avionics, I am generally a total noob. I've been flying airplanes...
  8. Replies
    3
    Views
    2,357

    OK, no-joy. Let me ask it this way... my ADS-B...

    OK, no-joy. Let me ask it this way... my ADS-B out was working fine with the old AFS 4500/Crossbow. When I switched it out for the 5400 with SV network, the ADS-B is no longer getting barometric...
  9. Replies
    3
    Views
    2,357

    ADS-B barometric altitude encoding problem

    Six months ago, I replaced my AFS4500 EFIS with an AFS 5400. After doing that, my avionics A&P noted a small static leak..OK for VFR, not IFR, he said. I then ran a PAPR and it showed a failure in...
  10. Replies
    12
    Views
    10,411

    I'll have to check, thanks. My situation is...

    I'll have to check, thanks. My situation is different from yours, though. My 5400 came with the v16 beta software, and although the 15.1 manual said there would be three positions ...UP - CENTER -...
  11. Replies
    12
    Views
    10,411

    The pinouts are correct, and I do get change in...

    The pinouts are correct, and I do get change in displayed adval as the flaps move. So although electrical damage to the POS is possible, I'm more inclined to think that there might be some actual...
  12. Replies
    12
    Views
    10,411

    No. I just checked it…the adval moves the same...

    No. I just checked it…the adval moves the same way as the display on the EFIS. That is, it doesn’t move smoothly/linearly throughout its range either. My previous 4500 didn’t do that. Is there a...
  13. Replies
    6
    Views
    5,840

    Interesting exercise. As is often the case, it's...

    Interesting exercise. As is often the case, it's never as easy as it looks on paper.

    On the EMS-to-network female connector, if found that a) the wiring colors were mostly different than the...
  14. Replies
    12
    Views
    10,411

    But they don't, Shawn. They do not interpolate....

    But they don't, Shawn. They do not interpolate. That's what these posts have been about. I even included a video in my first post (above), but sincerely I apologize for my inability to make my...
  15. Replies
    12
    Views
    10,411

    OK, thanks. I'm hooked up right then, correct pin...

    OK, thanks. I'm hooked up right then, correct pin 9, set to EMS.

    The 15.1 install manual page 184 indicates there would be full-up, center, and full down options on the flap calibration screen...
  16. Replies
    12
    Views
    10,411

    Hmmm...we did, but I don't recall specifically if...

    Hmmm...we did, but I don't recall specifically if moving pin 34 to pin 9 was part of that process. I'll have to check when I get back in there to jumper pin 7 to 5 on my EMS network harness to get...
  17. Replies
    6
    Views
    5,840

    Got it. Cut and terminate the orange wire, get 8...

    Got it. Cut and terminate the orange wire, get 8 volts from the red wire at pin 7 to pin 5.
  18. Replies
    12
    Views
    10,411

    Flap position -- all or none?

    5400 upgrade from non-functional 4500. I'm having trouble calibrating flap position. The 15.1 install manual page 184 indicates there would be a full-up, center, and full down entries but all I have...
  19. Replies
    6
    Views
    5,840

    The orange wire in the network cable to the EMS...

    The orange wire in the network cable to the EMS module isn't connected to anything? Just terminated and has no job in the SV-EMS-220?

    From page 135 of the 15.1 install manual...
  20. Replies
    6
    Views
    5,840

    Thanks Shawn

    Thanks Shawn
  21. Replies
    6
    Views
    5,840

    5400T - no fuel flow reading

    As I work through the last stages of my 4500 -> 5400 upgrade, I note that I have a fuel flow reading of zero. Looking over the manual, I see that page 135 of the 15.1 install manual says:
    "AF5000...
  22. Replies
    2
    Views
    4,027

    ..never mind...figured it out

    ..never mind...figured it out
  23. Thread: AF5500 help!

    by MacCool
    Replies
    3
    Views
    4,000

    I just went through this. I can't find any...

    I just went through this. I can't find any current documentation either. We struggled a bit calibrating my airplane until a call to Rob explained that the canopy had to be closed. My ADAHRS SV-200 is...
  24. Replies
    7
    Views
    34,923

    I just went through this. The YouTube video of...

    I just went through this. The YouTube video of Rob showing the calibration process isn't applicable to the version 16 software, apparently. We hauled my plane out to the airport's compass rose, and...
  25. Replies
    5
    Views
    7,527

    I saw that screen a couple of times on my 4500,...

    I saw that screen a couple of times on my 4500, then it changed to "AHRS OFFLINE", and that was all she wrote.
Results 1 to 25 of 54
Page 1 of 3 1 2 3