Search:

Type: Posts; User: Shawn McGinnis

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    21

    Lynx L3 NGT-9000 can be connected to any AF-5000,...

    Lynx L3 NGT-9000 can be connected to any AF-5000, or AF-3/4000s serial port using the configuration "ADSB 115K" when configured for GDL-90 protocol at 115200 baud.
  2. This is currently a requested feature, see...

    This is currently a requested feature, see http://advanced-flight-systems.com/forum/threads/1558-EarthX-Battery-Monitor

    It's a rather complicated thing as currently designed as there is no timing...
  3. Replies
    10
    Views
    4,599

    Have you verified your ADS-B out by requesting a...

    Have you verified your ADS-B out by requesting a PAPR? https://adsbperformance.faa.gov/paprrequest.aspx
  4. Thread: Mag cal

    by Shawn McGinnis
    Replies
    3
    Views
    2,133

    Ensure you have the SV-NETWORK properly...

    Ensure you have the SV-NETWORK properly functional by performing a SCAN on the PFD. Then you should have access to SET -> AHRS -> Hold MAG CAL. Ensure the the MAG CAL process has been presented on...
  5. Replies
    6
    Views
    5,680

    Go with the AOA pitot tube. Its much easier and...

    Go with the AOA pitot tube. Its much easier and the tubes are far less prone to issues. Wing ports will be less likely supported in future designs.

    Wing pressure ports are only more useful for...
  6. Replies
    4
    Views
    231

    Your MFD was probably not purchased with a...

    Your MFD was probably not purchased with a mapping key. Use CHECK -> MAINT -> (ABOUT) to see if your KEYS: has MAPPING. If it does you need an SD card with map data installed. Otherwise contact sales...
  7. Replies
    4
    Views
    231

    What feature / bug are you needing fixed?

    What feature / bug are you needing fixed?
  8. Replies
    17
    Views
    11,271

    I'm going to doubt that Garmin has released a...

    I'm going to doubt that Garmin has released a product with GDL-90 output. Any product with proper GDL-90 ADS-B out over 115K or 57K will interface to the AF-3/400s displays.
  9. Replies
    3
    Views
    1,241

    Ensure that you have not used AFS_DATA as the...

    Ensure that you have not used AFS_DATA as the label for the SD Card. Also verify that the card lock is UP closer to the pins. The card could also have not been ejected properly from the computer.
  10. Replies
    9
    Views
    2,851

    Yea, looking from the prospective of the MFD the...

    Yea, looking from the prospective of the MFD the Nav source, SL-30, is physically wired to a Remotely to the screen.
  11. Replies
    7
    Views
    2,051

    I've added your request for review. This fits in...

    I've added your request for review. This fits in with our IFR enhancements scheduled for the next major revision. As with all features the more interest in the feature the more quickly it will be...
  12. Replies
    9
    Views
    2,851

    Yes, disable the Serial Port 3 on the MFD. If...

    Yes, disable the Serial Port 3 on the MFD. If its wired to the PFD then the MFD should not be configured to expect a SL-30 wired to ITS serial port #3. The GPS/NAV Data Source 2 will then transfer...
  13. Replies
    7
    Views
    2,051

    The EFIS will draw the lead in arrow if you...

    The EFIS will draw the lead in arrow if you select the runway on the destination airport of the flight plan.
  14. Replies
    9
    Views
    2,851

    You will need the AF-ARINC module wired to one of...

    You will need the AF-ARINC module wired to one of the serial ports probably serial 4. This is what will drive the TruTrak.

    Something like...
  15. Replies
    1
    Views
    1,290

    The 912 can be interfaced to the 2500 using our...

    The 912 can be interfaced to the 2500 using our 71,420RX RPM Interface board. Call us at 503-263-0037 x 2 for ordering.

    The Rotax engines have a 5th trigger coil for RPM monitoring. The trigger...
  16. Replies
    7
    Views
    2,383

    https://www.advancedflightsystems.com/drawings-cad...

    https://www.advancedflightsystems.com/drawings-cad-models.php#AF-5000Wiring
    See our AF-5000 R7 EFIS Main Harness - w/ SV Network.

    You will find the locations to populate the SV Network pigtail...
  17. Replies
    15
    Views
    5,873

    Which port shouldn't effect the EFIS. Be sure to...

    Which port shouldn't effect the EFIS. Be sure to properly eject the drive from the computer.

    If this is a new drive be sure that you are using FAT32 filesystem and that the label is set to...
  18. This requires special modifications to the EFIS...

    This requires special modifications to the EFIS hardware and additional circuitry.
  19. Replies
    1
    Views
    1,239

    You don't. With the Dynon Pitot tube and...

    You don't. With the Dynon Pitot tube and SV-ADAHRS you will have AOA. This option is there for customers that are coming from wing-port systems that don't want to install the new pitot.
  20. Replies
    1
    Views
    755

    Checklists should have a 13 line limit. Title +...

    Checklists should have a 13 line limit. Title + 12 items. Ensure you are using 96 characters or less on all lines and that you have not used any commas. See page 112 (v15.0) of the pilots guide for...
  21. Replies
    2
    Views
    947

    Can you change to TRK?

    Can you change to TRK?
  22. Replies
    2
    Views
    1,522

    Try https://tfr.faa.gov (https://tfr.faa.gov/) or...

    Try https://tfr.faa.gov or the FAA UAS map https://faa.maps.arcgis.com/apps/webappviewer/index.html?id=9c2e4406710048e19806ebf6a06754ad

    Does it come and go with ADS-B?
  23. Replies
    2
    Views
    877

    Do you have the SV-AP-PANEL...

    Do you have the SV-AP-PANEL connected?
    Have you scanned for it in the Advanced SV-Network?
    Have you calibrated the trim in Elevator Trim calibration page?
  24. Replies
    15
    Views
    5,873

    Do you have the HRTERRAIN folder on the USB drive...

    Do you have the HRTERRAIN folder on the USB drive and is synthetic vision working properly? Post a picture of your CHECK -> ABOUT page, the bottom shows what GPS is feeding that data.



    SET ->...
  25. Replies
    4
    Views
    1,466

    You can send in the system logs and...

    You can send in the system logs and svautopilot.log files and we could take a look. If you haven't already, try re-running the servo calibration process.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4