Search:

Type: Posts; User: Cojaken

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    7,574

    Shawn, thanks for our telephone discussion. As a...

    Shawn, thanks for our telephone discussion. As a result of our conversation, I got a Mityvac MV8510 Silverline Elite Hand Pump, adapters and a gauge and used them to check the calibration of the new...
  2. Replies
    10
    Views
    7,574

    Thank you for the information Shawn. I just...

    Thank you for the information Shawn.

    I just made another observation. As you know when shutting off the master, the 3500EM switches to the internal backup battery for thirty seconds before...
  3. Replies
    10
    Views
    7,574

    It is not easy to physically follow the ground...

    It is not easy to physically follow the ground wire, so to eliminate this as a potential problem, I ran a new temporary ground wire directly from the sensor to the 3500EM case. The behavior was the...
  4. Replies
    10
    Views
    7,574

    0-2 bar is stamped on the hex of the sensor

    0-2 bar is stamped on the hex of the sensor
  5. Replies
    10
    Views
    7,574

    Thanks Shawn. I measured the voltage supplied and...

    Thanks Shawn. I measured the voltage supplied and the resistance across the disconnected sensor at zero pressure.

    The resistance is 9.5 ohms.

    The voltage on pin 8 of the Engine Sensor connector...
  6. Replies
    10
    Views
    7,574

    Bad fuel pressure sensor or bad calibration?

    I recently ordered and fitted a new replacement VDO fuel pressure sensor part # 41215, for my 3500EM non-S. I did this because the fuel pressure reading became erratic after about 270 hours.

    The...
  7. Replies
    1
    Views
    77,254

    XM Radio volume control on 5400T

    I'm on the Check - Radio page and can see the volume sitting at zero. I can't turn up the volume with either of the two knobs or the touch screen.

    How do you control the XM Radio volume on the...
  8. Replies
    0
    Views
    74,160

    5400T not sharing XM with 3500EM

    I have a 5400T PFD and a 3500EM non-S. Both have the latest available system software and map files.

    My XM weather, which comes from a WxWorx receiver will display on whichever of the two screens...
  9. Replies
    10
    Views
    346,431

    I do appreciate your input Bob. I can’t help...

    I do appreciate your input Bob. I can’t help thinking I must have ADSB from a tower if I am at 3000 ft in class C airspace and I think the fact that I have weather confirms this?

    This “No radar”...
  10. Replies
    10
    Views
    346,431

    I too would like a clarification of what "No...

    I too would like a clarification of what "No Radar" means. The manual says:

    "ADS-B system is reporting that it does not know about radar traffic targets, or that it is
    not receiving information...
  11. Replies
    2
    Views
    96,515

    I like this suggestion.

    I like this suggestion.
  12. Replies
    1
    Views
    11,419

    It was indeed a bad ethernet cable from the...

    It was indeed a bad ethernet cable from the AF5400T to the hub.
  13. Replies
    1
    Views
    11,419

    Ethernet hub issues

    When my two screens are connected together with an ethernet cable, they talk to each other.
    When they are connected via a hub, they do not.
    My AF3500EM talks to my Wxworx XM receiver via the hub....
  14. Replies
    4
    Views
    16,814

    I have a 3500EF and a 3500EM. If I upgrade the...

    I have a 3500EF and a 3500EM. If I upgrade the 3500EF to a 5400, will it display data from the 3500EM and will the EM display data from the 5400 please?

    Colin Kennedy
    RV-9A
    Oklahoma
Results 1 to 14 of 18