View Full Version : Pre-installed AOA data
dnelson
10-26-2011, 02:48 AM
Hi Trevor,
How can I tell if the pre-installed AOA data on a 4500 is for an RV-7A?
Thank you,
/\/elson
dnelson
11-03-2011, 06:53 PM
Anybody home?
Rob Hickman
11-04-2011, 01:27 PM
RV-4, 6, 7, 8 Data
ZERO_LIFT_CRUISE, 67
PERFORMANCE_CRUISE, 680
APPROACH_CRUISE, 884
WARNING_CRUISE, 1242
CRITICAL_ANGLE_CRUISE, 1650
ZERO_LIFT_LANDING, -175
PERFORMANCE_LANDING, 599
APPROACH_LANDING, 779
WARNING_LANDING, 1310
CRITICAL_ANGLE_LANDING, 1826
AOA_AUDIO, 1
AOA_ENABLE, 1
LANDING_OVERRIDE, 80
USE_FLAP_ANGLE_SENSOR, 0
CRITICAL_AOA, 150
DECLUTTER_SEGMENT, 8
Jim Berry
11-04-2011, 07:15 PM
Rob,
Can you provide the same data for the RV-10? Thanks
dnelson
11-04-2011, 08:04 PM
Thank you, Rob.
tomhanaway
11-05-2011, 02:57 PM
Ditto :^) --smiley face added to get up to ten characters required for post......
Rob,
Can you provide the same data for the RV-10? Thanks
Rob Hickman
11-05-2011, 05:35 PM
From my RV-10:
ZERO_LIFT_CRUISE, 161
PERFORMANCE_CRUISE, 789
APPROACH_CRUISE, 999
WARNING_CRUISE, 1366
CRITICAL_ANGLE_CRUISE, 1785
ZERO_LIFT_LANDING, 179
PERFORMANCE_LANDING, 346
APPROACH_LANDING, 681
WARNING_LANDING, 1338
CRITICAL_ANGLE_LANDING, 1741
AOA_AUDIO, 1
AOA_ENABLE, 1
LANDING_OVERRIDE, 80
USE_FLAP_ANGLE_SENSOR, 1
CRITICAL_AOA, 150
DECLUTTER_SEGMENT, 8
kbehrent
01-08-2012, 03:43 PM
How about a RV-9A?
Rob Hickman
01-08-2012, 05:41 PM
I will see if I can get it.
flycirrus
03-14-2013, 11:31 AM
I have verified my setting are preloaded, however I have 3 parameters that are different. It is an RV7A.
My Zero lift setting is 68 (not 67)
My Landing Override is 8.0 (not 80)
My Critical AOA is is 15.0 (not 150)
The zero lift setting is close, the others are an order of magnitude off. Is this just a newer set of numbers or do I need to change to those to your posted settings?
Thanks
Roger
RV-4, 6, 7, 8 Data
ZERO_LIFT_CRUISE, 67
PERFORMANCE_CRUISE, 680
APPROACH_CRUISE, 884
WARNING_CRUISE, 1242
CRITICAL_ANGLE_CRUISE, 1650
ZERO_LIFT_LANDING, -175
PERFORMANCE_LANDING, 599
APPROACH_LANDING, 779
WARNING_LANDING, 1310
CRITICAL_ANGLE_LANDING, 1826
AOA_AUDIO, 1
AOA_ENABLE, 1
LANDING_OVERRIDE, 80
USE_FLAP_ANGLE_SENSOR, 0
CRITICAL_AOA, 150
DECLUTTER_SEGMENT, 8
Rob Hickman
03-14-2013, 03:47 PM
My Zero lift setting is 68 (not 67) Close enough
My Landing Override is 8.0 (not 80) 80 in the file is 8.0 on the screen it gets divided by 10
My Critical AOA is is 15.0 (not 150) 150 in the file is 15.0 on the screen it gets divided by 10
flycirrus
03-14-2013, 08:04 PM
Rob,
Thanks for the quick reply.
BTW, my plane is red where the port decals go, amazingly close to the color of your decals - not much contrast at all. Do you have them in other colors like white that I can buy?
My Zero lift setting is 68 (not 67) Close enough
My Landing Override is 8.0 (not 80) 80 in the file is 8.0 on the screen it gets divided by 10
My Critical AOA is is 15.0 (not 150) 150 in the file is 15.0 on the screen it gets divided by 10
Rob Hickman
03-15-2013, 08:16 AM
We have a paint mask.
Blain
04-16-2017, 11:14 AM
The default preload for my RV-8 feels better then after the calibration. How can I load the settings listed above to get back to the factory configuration?
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions Inc. All rights reserved.