PDA

View Full Version : ADSB Targets on the Avidyne IFD-540



capdave
09-11-2020, 02:48 PM
Hello all,
Am I supposed to be getting ADSB targets displaying on the avidyne screen as well? I have configured everything to the latest software and adsb works great on the 5600 screens. I get a "429 data not received" message as well as a datalink error message. all ports are set as described in the install manual.

rvdave
09-11-2020, 09:14 PM
You should not get the 429 data not received or datalink error message if everything is wired and configured correctly, but you also won’t get traffic to ifd540. You should get weather though to ifd. Just went through this.

Edit: You can get traffic to ifd540 but there is no way to filter your ownship and you will get annoying traffic warnings, so I just turned it off to ifd.

capdave
09-12-2020, 06:42 AM
Hi,
Thanks for the response. Is there any way that you can post your ifd dat settings as well as your serial port settings ifd on the asvanced screens? I know that the wiring is correct...I'm sure that it is just a setting. Thanks in advance.

rvdave
09-12-2020, 11:37 AM
Next time at the hangar I’ll get some photos

capdave
09-12-2020, 01:39 PM
Thanks! Id appreciate it.

rvdave
09-12-2020, 10:28 PM
Not sure if you went through this but here is setup from afs manual.

rvdave
09-13-2020, 08:03 AM
Hope this helps

501

502

503

504

capdave
09-15-2020, 06:05 PM
Thank you! I will take a look at these settings tomorrow when we fly.

Rob Hickman
09-17-2020, 04:27 PM
The setting in the last picture is not correct. You should have it set to: capstone HS TRFC+WX

rvdave
09-17-2020, 06:08 PM
The reason I turned traffic off was because my ownship was always showing up on ifd550 triggering an annoying traffic alert. From what I understand there’s no way to filter ownship from ifd550 so I just use weather since I have traffic with afs.

Rob Hickman
09-18-2020, 11:27 AM
The Dynon ADSB receiver does not filter out your own aircraft, with an AFS or Dynon EFIS the ownship filtering is done by the EFIS. The Avidyne IFD is expecting the ADSB receiver to filter out your ownship. We are working on the software to filter out your ownship and it is complicated. The EFIS is generating the audio traffic warnings so having your own aircraft on the IFD is only a small nuisance.

Rob Hickman
09-18-2020, 11:31 AM
Hello all,
Am I supposed to be getting ADSB targets displaying on the avidyne screen as well? I have configured everything to the latest software and adsb works great on the 5600 screens. I get a "429 data not received" message as well as a datalink error message. all ports are set as described in the install manual.

The 429 data not received has nothing to do with the RS-232 serial ports. Send me an email with the system logs from both EFIS screens Rob@Advanced-Flight-Systems.com

capdave
09-23-2020, 09:05 PM
Hi,
Ok thanks ...will do. I think that everything is working corrctly now except for a crossed out tis-b message at the top of the ifd display. Is this normal?

Rob Hickman
09-25-2020, 08:37 AM
Hi,
Ok thanks ...will do. I think that everything is working corrctly now except for a crossed out tis-b message at the top of the ifd display. Is this normal?

Yes, we are working on a solution with Avidyne.

mguenin
09-25-2020, 09:06 AM
Is v15.2 of the install manual available? The link on the website delivers the v15.1 version.

Rob Hickman
09-28-2020, 02:34 PM
We should have an updated manual on the web site next week.