PDA

View Full Version : Engine Sensor Installation Questions



  1. Aux Temp Sensor(s)
  2. MAP sensor - hot or cold side of firewall?
  3. Sensors for AF2500 vs 3500EE
  4. Capacitance sending units---Right tank single set point, left tank two set point
  5. Rotax 914 Fuel Pressure on AF3500s
  6. MAP and % Power Troubleshooting
  7. Erratic Oil Temp
  8. OP sender location/ installation
  9. Flux for soldering EGT, CHT
  10. New Feature Request ? - Displaying Electronic Ignition Timing
  11. Hall Effect Current 'Ducer Miswired at factory
  12. Fuel Pressure sender failure
  13. Tachometer and Percent of Power Slow to Come Alive
  14. Bendix vs Slick
  15. Engine Sensor Harness - Black Wires
  16. Low manifold pressure indication
  17. Oil/Fuel PSI only seem to work during internal battery ops
  18. Rocky Mountain Senders
  19. FP reading
  20. Source for EGT/CHT non-insulated barrel terminal
  21. Oil Pressure Transducer
  22. Troubleshooting "No RPM" indication
  23. %HP indicating 1/2 actual on FADEC
  24. Manifold tubin question
  25. Use of Van's instrument transducers
  26. Amp reading
  27. Extending EGT/CHT cables
  28. Fuel/Oil Pressure Calibration
  29. EGT/CHT Sleeving
  30. Fuel calibration
  31. RPM slow to show
  32. Sensor Calibration
  33. Fuel Pressure Sensor Location
  34. RPM sensor question with Slicks
  35. pmags rpm
  36. RPM install with LASAR Electronic Ignition
  37. 2 Current Sources
  38. Fuel press on the 4500 shows 10 PSI with engine not running
  39. K Factor
  40. Fuel Guage
  41. Manifold Pressure Installation Questions -- RV-7A
  42. Bad EGT fixed.
  43. Fuel Pressure and Oil Pressure pegged high
  44. Fuel level AD_Value stuck at zero
  45. Circuit protection for shunt wires
  46. EGT/CHT cables - OK to reduce excess length?
  47. Interchangable Thermocouples?
  48. How to calculate Tank 1&2 fuel level AD_Value?
  49. RPM not displaying
  50. #4 CHT erratic
  51. Oil temp sensor vs. kitchen thermometer in heated oil
  52. Three Sensor failures in less than 60 hours
  53. Wiring fuel, oil sensors
  54. Carb temp options?
  55. Grounding oil temp probe
  56. Rotax 914 Fuel Flow Wiring
  57. Rotax CHT Wiring
  58. What's needed to convert to using Kavlico sensors for a 4500?
  59. Fuel Flow Calibration
  60. EGT and CHT Reading Errors
  61. Manifold Pressure Sensor Calibration
  62. MAP Dampening
  63. Red Cube failure?
  64. Shunt interchange
  65. CHT difference
  66. Kavlico Oil Pressure Sensor and Hobbs Meter
  67. Reset Tach Time
  68. vdo oil pressure
  69. RPM display with mixed ignitions
  70. RPM Sensor - Part number or brand or place to buy.
  71. Floscan 201
  72. Tachometer and exhaust gas sensor replacement
  73. Type J or K CHT probes
  74. RPM indication with emags
  75. RPM with E-Mags
  76. replacement red cube
  77. EGT readings off the top of the sensor range
  78. Dynon Engine Sensor Kit
  79. B & C alternator, external LR3C Voltage regulator
  80. New style Kavlico sensor for fuel pressure
  81. Bad Hall Effect sensor for Amperage reading?
  82. Oil temp sensor replacement?
  83. Oil pressure switch?
  84. Fuel flow voltage